PDA

View Full Version : how do create blank tp file? unable to delete 1 tp on 110



ftastudent2
01-18-2014, 01:57 AM
Trying to create an empty tp file to use with the new tp update file but cannot delete 12311 on 110. Now my wiz 110 won,t connect after a system clean file was loaded, still working on that but for now would be happy to have a file without any tp,s on 82.92.110.118.7.119 and 129.
How can this be achieved without screwing up your Wiz 110 Card?
Also if you have any advice for the wiz 110 card to get it to hook up, that would be helpful. On boot it always says reboot because it can,t connect. Not exact wording but that's what it means.

Sp0iler
01-18-2014, 11:45 AM
Next time, unplug the dongle when your working with the box.
What file is currently loaded in the box ?
Is it the "no-chk" file ? It needs to be.
Use Wiz and confirm the version of the dongle.Also confirm the baud rate "Speed" is set to 115200
If your at version 82, try to load the svlan-43 file followed by the 4.12 firmware file.

No help for your transponder issue.....

ftastudent2
01-18-2014, 02:45 PM
Yup, I figured out that you need to unplug but too late.
Card is at 4.12 and STB proper file too 21? or something. Have it out of system now and using hated Limesat.
I have done system clean, loaded factory file and done factory reset onm stb. Then pluged in card and received same result.
I currently have card hooked up to laptop but am unable to connect with Wiz tool. I use this laptop for Rockwell software and rslinx claims the com port. Even after stopping rslinx I cannot connect. Do you know prper port settings? Baud rate, Data bit, Parity, Stop bit and flow control settings?

skywalker999
01-18-2014, 02:58 PM
hum and after the system clean file did you load the proper file after that hummmm :noidea:

junior1
01-18-2014, 03:32 PM
Yup, I figured out that you need to unplug but too late.
Card is at 4.12 and STB proper file too 21? or something. Have it out of system now and using hated Limesat.
I have done system clean, loaded factory file and done factory reset onm stb. Then pluged in card and received same result.
I currently have card hooked up to laptop but am unable to connect with Wiz tool. I use this laptop for Rockwell software and rslinx claims the com port. Even after stopping rslinx I cannot connect. Do you know prper port settings? Baud rate, Data bit, Parity, Stop bit and flow control settings?

The current file is HD20-2028, located here...http://www.satfix.net/showthread.php?119203-SV8000HD-HD20-bin-CCE-Fix-May-05-2012
Databit is 8, Parity None, Stop Bit 1, Flow Control None. Port settings 80 on top and 1920 on the bottom. Make sure you save your settings after making any changes.

ftastudent2
01-18-2014, 04:53 PM
I just finished hooking it up to a computer monitor so now I can be precise.
STB at HD20E which is the HD-2028 file. Wiz110 is at 4.12 but it still gives the error which I cannot see on the monitor as HDMI sets only after the STB has fully booted. Network does not appear in install menu.

airjam
01-19-2014, 03:50 AM
I just finished hooking it up to a computer monitor so now I can be precise.
STB at HD20E which is the HD-2028 file. Wiz110 is at 4.12 but it still gives the error which I cannot see on the monitor as HDMI sets only after the STB has fully booted. Network does not appear in install menu.

You have not loaded the correct BIN for the WIZ110SR .... The correct file can be found here post #4
http://www.satfix.net/showthread.php?133881-Sonicview-Hub-Emulator-Program

airjam
01-19-2014, 03:58 AM
The current file is HD20-2028, located here...http://www.satfix.net/showthread.php?119203-SV8000HD-HD20-bin-CCE-Fix-May-05-2012
Databit is 8, Parity None, Stop Bit 1, Flow Control None. Port settings 80 on top and 1920 on the bottom. Make sure you save your settings after making any changes.
That file will not work with the WIZ110SR .... He needs the no-chk file