Hello gang, I have tried Blind Scan with Network Search ON and OFF and still channels like 307, 526 are missing, any ideas?
Hello gang, I have tried Blind Scan with Network Search ON and OFF and still channels like 307, 526 are missing, any ideas?
i be leave that box is like a jynxbox to get all the channels try this :
the easiest way that i found is the do a factory reset. then reset your setting for your sats .
To get sat 110 back go to manual scan, change the first tp to the new mpeg4 setting by selecting edit tp red button on remote then change symbol rate from 20000 to 21500 and change the polarity to v then change Mode from QPSK TO TURBO then save . now you should see good signal on the first tp. Now go to the #2 tp and use the yellow button on remote and delete all the remaining tps just leave the first tp there .
Ones all the remaining tps are deleted hit the blue button on remote to scan then set network search to YES then hit ok and all channels will scan back in with good signal . now hit the side arrow on remote to get to sat 119
For 119 when your in the manual scan set to 119 sat, if the first tp has quality and strength , then leave the first one alone and delete all the rest of the tps for 119 then hit the blue button on remote set network search to YES then hit ok to scan and you will get all channels after your done go to tv channels in menu hit the blue button on remote to edit then hit red button on remote set to sort SELECT by SID exist and save . finished.
ps if you do not delete the remaining tps and set NETWORK SEARCH to YES you will get all double channels .
PLEASE Do NOT PM me for support! Post ALL Support questions in the forums for all members to benefit.
You are correct, it is a clone of the JynxBox, when friends have JynxBox Clone with over heating problems I load those clones with AZlink Software and problem is gone.
I did like you said but the 307 Does Not Exists. Now if I do a factory reset and without changing anything I do Auto Scan with Network Search OFF it scans like 80 channels and 307 is there, I checked the TP to make sure I don't loosse channel again and the TP is 12224 V 21500 then I delete all TPs but the first all channels show but now the 307 is a NO SIGNAL.
can you manual scan the tp?
try scanning just that tp 12224 on sat 110 as nobodyspecial suggested and if you get 307 working , if that don't work can you post your dish set up , type of lnbs etc.. just so we no what we can suggest you to try
PLEASE Do NOT PM me for support! Post ALL Support questions in the forums for all members to benefit.
Down in the Jynx section I suggested that folks start manually editing the channel lists rather than rely on scans since there seems to be lots of issues with them. Perhaps that is something you could try instead. I spent some time looking at the ch list format and it seems straight forward so I would think it an easy project.
http://www.satfix.to/showthread.php?...-scan-question
Found the problem, can't scan sats with switch in between, I connected STB directly to LNB deleted all TPs but one, auto scan with Network Search YES and now all channels seems to be there.
The setup is
Cal-Amp LNB for 110
Eagle Aspen LNB for 119
22KHz Tone Switch
JB200+ 650miliamp
I tried a SW21 Microyal but quality signal drops 3% I also tried a Diseq Switch Quality signal stays same % as with the 22Khz the receiver seems to scan from any port mixing frequency from both sats the only way to scan correctly is direct connection to each LNB. I was thinking to run 2 cables to the receiver with a second JB200 and use 1 JB200 for 119 and the second JB200 to 110.
Thanks for the help guys.
Jynxbox only supports Diseq Switch they never worked with sw21 and when the Diseq Switch does not work its mostly the JB200 is going or week had a couple of them bad right out of the box receiver would only work ok with one sat . changed out the tuner and it work ok
Last edited by marcel.crash; 03-27-2017 at 11:33 PM.
PLEASE Do NOT PM me for support! Post ALL Support questions in the forums for all members to benefit.