91/82 119/110 /129 /97w SatS

[Novk10]

So what switch to make all 6 sat to one reviever. I only got 5 sat to works that 's it . So here how i did i used Diseqc switch 4x1 and sw21 switch. sat 119/110 sw21 to port 3 both works good. But if i do same thing on 91/82 useing sw21 to DiseqC 4x1 will not work both like 119/110. If 91w work the 82w will not work.If 82w work the 91w not working. I had Dish 500 with LNB DSS all sat except 97W. Can any one tell me what i can do make all works anyidea.

[kak]

First of all, you can not have all those satellites with dish 500, what you need is :
Either you can use 2 dishes or one big dish 39' for fta, with this one you can have a bracket that holds 6 LNBF, you put the lnbf for 97 west in the center, then you add the other sats besides with the exact degrees between each lnbf, this one is gonna be little challenge for you to get a very strong signal if you know how to do it, so you only can use 1 big dish.
The second option is to have 2 dishes which is the best way for you if you want to have all these setellites working.
My suggestion is to have dish 1000+ that comes with 3 lnbf and you can add the the 4 one for sat 129, so with this dish now you have 119, 110 and 129 all in one dish, then you have to have the second dish 39' the big one for fTA, and you can add a bracket for the 2 lnbf 91/82, you always have to put the LNBF 97 W in the center, then 91/82 besides, don't use the twin for 91/82, use the single ones, one for 91 and the other one for 82.
after you get all these satellite with great signals, then you have to use 3 switchs, one DP44 switch with the power inserter, then 2 SW21 switchs.
the 44 switch has 4 sats in and 4 out for 4 receivers, the way how you gonna do this:
Port 1 for sat 119
port 2 for sat 110
port 3 for sat 129
port 4 for 91
Now all these sats with this order are going to 44 switch
the 4 outs to 4 receivers, use the 1 one out hocked up to the power inserter, just the power inserter, not to the receiver, after doing this, now you have 3 ports out free from the 44 switch, now use one jumper coax cable from out 2 from 44 switch to SW31 switch in where it says sat1 sat2 in, put it in sat1, then bring another coax cable from the big dish 39' from sat 97 W comming from the center, then put it on sat 2 of SW21 switch, after this take the out cable from that SW21 swich where it says to receiver and put it in the second SW21 switch in Sat 1 port, the sat 2 use it for the last LNBF wich is 82 in, then the out from the SW21 goes straight to your receiver.
when you go to configure your receiver, depending on wich receiver you have, 119 port 1, and KHz has to be on not off, then the option of SW 21 switch either 1 or 2, then do 110 port 2,129 port 3, 91 port 4, for 82 and 97 just use where it says legacy SW21 ! or 2 for both 97 and 82, and that should be it.
Good luck , let me know how it work.

[bettie]

So what switch to make all 6 sat to one reviever. I only got 5 sat to works that 's it . So here how i did i used Diseqc switch 4x1 and sw21 switch. sat 119/110 sw21 to port 3 both works good. But if i do same thing on 91/82 useing sw21 to DiseqC 4x1 will not work both like 119/110. If 91w work the 82w will not work.If 82w work the 91w not working. I had Dish 500 with LNB DSS all sat except 97W. Can any one tell me what i can do make all works anyidea.

You can only use 1 sw21 switch in a cascade....so put your sw21 switch first....then your diseqc switch connected to one of the inputs on the sw21...then use a 22khz switch for your 2 remaining sats and connect to the other input on the sw21.

Or....skip the sw21 and use 22khz switches for 2 sets of sats....going into your diseqc switch.

[Novk10]

I have 2 dishes 500. 1 for 119/110 and second for 91 /82 the LNB all single DSS . the 97W use Universal LNB got 36' Dish for FTA and for 129W I use Direct tv Dish by inself.If i use the same set like 119/110 to sw21 switch then to DiSeqc switch only 119 /110 works both when change channels. But for the 91/82 only one work I don't know why? Oh! I have a Dreamlink HD reciever. Any one if you can make me pictures i apreciated.

[Novk10]

I'm talking about switches . The Dishes is all been set up. so how do you get all 6 sat in to the switches to works all 6's sat. thanks in advances.

[satchick]

You can use two Diseqc switches, and combine the outputs using an SW21 or Ecoda 22K switch.

[Novk10]

Is 8x1 Gastone DiseqC switch going to work or not? It support DiseqC 1.1 switches. anyone have this switch is going to work yes or no? .

[Novk10]

Okay have bougth Gastone 8x1 Diseqc Switch and i try it on my Dreamlink HD it work all ports perfectly. But when try on my Nanosat SE did not work all ports only port 1 througth 4 that's it and don't know why.