files for duo (windows 7 & iks)

[cgc]

xx-client is set up and waiting for request. On the receiver the guide is setup and 101 has video and audio, all the rest are scramble. I need instructions on how to set up the receiver and the files to install. Thanks

[jeldf]

Post your menu settings - system information and utility settings

[cgc]

Menu:
Keyworks: autoroll off, EMU on

System:
SW: MVO2.53 (May 15) LDR 1.08
HW VER: 1.00
Duo/trio (4)
RS232 Mode: Normal
Using a serial cross over cable

Running Win 7

Thanks

[1boxman]

Hey cg


you need these files for receiver .
CNX DUO
Factory:DTP_516_Factory_UPB 2/10/10
Third Party:DTP_253_UPB 5/22/10

and null cable

[jeldf]

You can't help but use a null modem as the STB and PC both have male ports. Are you using a COM port or USB to serial? Check the port # in device manager and make sure it matches the Port in the Conf File. When connected you should get the following.

SW: MVO2.53 (May 15) LDR 1.08
HW VER: 1.00
Duo/trio (4)
xx-client v1.14

Also, EMU=off
RS232=Dongle, IP Setup, IKS

[dishuser]

You can't help but use a null modem as the STB and PC both have male ports. Are you using a COM port or USB to serial? Check the port # in device manager and make sure it matches the Port in the Conf File. When connected you should get the following.

SW: MVO2.53 (May 15) LDR 1.08
HW VER: 1.00
Duo/trio (4)
xx-client v1.14

Also, EMU=off
RS232=Dongle, IP Setup, IKS
male ends have nothing to do with serial or null...lol

[cgc]

SW: MVO2.53 (May 15) LDR 1.08
HW VER: 1.00
Duo/trio (4)
unknown

Com port settings are the same in the device manager and the xx client

RS232=Dongle, IP Setup, IKS

now the receiver is off service

(I setup coolsat 5000 like a snap, why is this duo driving me crazy)

Thanks for the help.
cgc

[jeldf]

I will flash my Nano to a Duo and see if I can get it to work with those settings i love testing. Will let you know how it works out.

[dishuser]

I will flash my Nano to a Duo and see if I can get it to work with those settings i love testing. Will let you know how it works out.

can't be done

[jeldf]

beg to differ......CNX Mini, Duo, Trio, Nano can all run each others software. been there, done it. Remotes become a little weird but you can always make one that will work.

[cgc]

Device Manager
com0com - serial port emulators
-com0com - bus for serial port pair emulator
-com0com - serial port emulator
-com0com - serial port emulator


ports (COM & LPT)
Bits per second 115200
Data bits 8
Parity NONE
sTOP BITS 1

XX-Client

[General]


serial_port=\\.\CNCA0
emulator_serial_port=\\.\CNCB0
receiver_serial_port=COM1
receiver_timeout=200
receiver_byte_read_delay=250
server_byte_read_delay=100
serial_port_settings=115200|8|N|1
byte_write_delay=50
receiver_protocol=0
caid_mappings=1840:1816
background_execution=0
debug_level=1
log_to_console=1
log_to_file=0
logfile_name=xx-client.log
control_words_timeout=12
card_server_url=newcamd://xxxxxxxx:[email protected]:99999/123456789123456789123456789

Client ready -Waiting for request

Receiver Configuration:

System information
SW:MV02.53 (May 15) Ldr 1.08
HW Ver. 1.00
USB 2.0 Driver: 1.00
Duo/Trio (4)
Unknown

Key Works
Key edit System1 Nagra
Reset data - not touched
auto roll, bev, dish - off
Emu - OFF


RS-232 Mode
Type - Normal
network - Network settings - not used (no addresses entered)
Registration IKS - registration failed

Null serial cable


If I set RS-232 Mode to Dongle then I get off service on the receiver.

[cgc]

So what is the set up procedure for the duo receiver. emu-off, rs232, is dongle or normal. do I enter ip addresses.

[dinkish]

CNX Duo bins:
Factory: DTP_516_Factory_UPB
Third Party: DTP_253_UPB

CNX Settings:
emu = off
rs232 = normal

xx-client:
Receiver protocol to emulate = 1

You enter your private server info in xx-client and it should work at this point. Are your com0com virtual settings correct?

[jeldf]

set rs232 to normal and I lost Snookie lol. rs232=dongle ;-) are you using USB to serial? you need to allocate the USB to Com1 in Device mgr for it to work with com0com.

[wallybeaver]

HELP PLS

i am trying to setup my cnx duo for private iks and i am sooooo lost
i have installed xx-client and such and when i go to run it keeps saying it cant find cncb0 i am using windows xp

[Glock20C]

google com0com to install serial port emulators

[Kaldar]

is it possible to make xx client switch to 2 servers. Automaticaly ? One for b and one for d ?

[jeldf]

run xx-client WIZARD and that will make all well.