low quality on signal jynxbox

[vago]

hi i receive today a new jynx and for my surprise am having a low S and Q on signal get 63 and on quality 63 my setting are 11250......diseqk 2 for 110 and 11250....... diseqk 3 am using diseqk with separate lnbs circular if i conet my limesat ultra signal goes on quality up to 95 on 110 and 02 on 119 also scaning with jinx only scan 70 channels on 119 and 236 on 110 am doing blind scan whats wrong is a bad or defective receiver.

[Nostradamus]

sounds more like you have a LNB setting wrong or your dish is slightly out of alignment. As for the difference in signal readings, well the Limesat Ultra never worked properly. Always read too high! And Jynx reads lower than some. Rule of thumb is if you have a solid picture and rain fade is not an issue then don't mess with things or worry about numbers. If you can't improve signal any by adjusting LNB settings then it might be time to tweak the dish

[vago]

dish is perfectly aligned so this morning i went straigth to 110 no disequk very low quality is the first time experience this kind of problem i know that sv8000 when the 8psk fail same thing happen but this is brand new i opened yesterday thanks

[vago]

i will send it back tomorrow and wait for a good one think is the j100

[rusty121]

hi i receive today a new jynx and for my surprise am having a low S and Q on signal get 63 and on quality 63 my setting are 11250......diseqk 2 for 110 and 11250....... diseqk 3 am using diseqk with separate lnbs circular if i conet my limesat ultra signal goes on quality up to 95 on 110 and 02 on 119 also scaning with jinx only scan 70 channels on 119 and 236 on 110 am doing blind scan whats wrong is a bad or defective receiver.

If you are using a Di*h pro lnb you need to change your settings (see atachment)16493

[vago]

no am using two separate lnbs with diseqc and a second dish for m129

[iq180]

did you go to lyng sat and check your TPs and your SR, on the jynx box if the jb100 module is bad your S&Q will be under 48%
so i dont think it is bad, i think it is your settings.

[Anubis]

hi i receive today a new jynx and for my surprise am having a low S and Q on signal get 63 and on quality 63 my setting are 11250......diseqk 2 for 110 and 11250....... diseqk 3 am using diseqk with separate lnbs circular if i conet my limesat ultra signal goes on quality up to 95 on 110 and 02 on 119 also scaning with jinx only scan 70 channels on 119 and 236 on 110 am doing blind scan whats wrong is a bad or defective receiver.

Diseq one should be port one for 119 and diseq 1 port 2 should be 110 assuming you have them plugged in the switch that way. If not it could be reversed and 110 is port 1 and 119 is port 2. Try either way to see if your signal goes up for you.
Turn network setting to on and don't do a blind scan. Do a normal scan.

[rusty121]

no am using two separate lnbs with diseqc and a second dish for m129

Legacy lnb works poor on the Jynxbox, on my case, when i switch to the lnb pro i went from 125 channels to over 600. (see a D*sh Pro picture) 16496

[vago]

i try in my neighbor housen with a diferent antena he only uses 110 so i tested and the signal and quality only shows 40 and 40 and if do blind scan only 23 channels if do normal scan nothing and when check video it works but as soon it warms say one hour and turned off and later turned on say no signal so i allready returned thanks for the reply friends

[phat]

You probably have a bad JB100.

I have legacy LNB's and have 80% signal strength.