Nano Premium doesn't work

[Manilo]

It looks like the codes are ok, however I just realized that the Nano Premium doesn't work if my other receiver (limesat) is on and viceversa. I sent a donation for each receiver, so I don't understand why they can't work at the same time. Any suggestion? Is this normal?

[chuck]

It looks like the codes are ok, however I just realized that the Nano Premium doesn't work if my other receiver (limesat) is on and viceversa. I sent a donation for each receiver, so I don't understand why they can't work at the same time. Any suggestion? Is this normal?

simple fix try a hard boot.

are both recievers hard wired or you useing powerline adaptors?
you have both codes entered in each box....useing server 1/2?

[Manilo]

One is hard wired and the other one powerline adaptor
simple fix try a hard boot.

are both recievers hard wired or you useing powerline adaptors?
you have both codes entered in each box....useing server 1/2?

[hutch]

Don't put both codes in both boxes ... only one receiver per code

[Manilo]

That's what I did, although the only difference in those codes are the domains for each receiver
Don't put both codes in both boxes ... only one receiver per code

[gwrowe]

The one receiver is powering over the other, had this problem before, it has got to do with your switch, go get a 22khz, the type that you can connect both sat's into 119/110, and it has 4 ports for for receivers, this sw will fix your problem, when you setup this sw in your antenna setup, no need to enter any ports in the disec 1.0, you just have to turn on the 22khz for either 110, or 119.

[Manilo]

What about sat 91?
The one receiver is powering over the other, had this problem before, it has got to do with your switch, go get a 22khz, the type that you can connect both sat's into 119/110, and it has 4 ports for for receivers, this sw will fix your problem, when you setup this sw in your antenna setup, no need to enter any ports in the disec 1.0, you just have to turn on the 22khz for either 110, or 119.

[gabrilius]

If i well understand we must to put the same info in both receiver and the only diference is the server 1 versus server 2 right

[Glatt]

How can 2 codes have the same number that is impossible!

[hutch]

I'll say it again... If you only have 1 code it will only work one receiver


Don't put both codes in both boxes ... only one receiver per code

[gabrilius]

in 2011 i was with rocket and i was 1 code for both receiver and the diferrences settings in each recv was only the port number, but now with nfps, i lost the info for one of the receiver and then i check my info on the oficial site they give me just 1 port,doesnt work both recv in the same time. i suppose because they dont have a marck for how many recv i subscript?

[davescarbs]

is you runnin seprate cables from each reciver to the lnb

[gwrowe]

For connecting the 91 you will also need a 3x4 sw, go to the hardware discussions forum there you will get the wiring diagram to do this, as for your codes, enter your DN info to server 1, and your B3V into server 2. Back then, it was 1 code and 2 ports for 2 receivers that has changed now, 1 code per receiver, 2 receivers 2 codes, you will have 2 get another code for the other receiver, for DN as well as B3V.

[Manilo]

I received a new code to fix the problem, but another issue came with my Limesat. The remote or the screen does not have a key to input a hyphen.

Does any one know how to input a "hyphen" or a comand to get the hyphen. Thanks!

[Manilo]

Never mind. I found the hyphen
I received a new code to fix the problem, but another issue came with my Limesat. The remote or the screen does not have a key to input a hyphen.

Does any one know how to input a "hyphen" or a comand to get the hyphen. Thanks!