viewertrex
12-27-2012, 06:55 PM
since i started over with my upgrades with the viewsat, i need to set up the wfemu 4 windows again. i am stuck at the step after installing the 322 bin. the caid map packet does not show on my wfemu 4 windows. help :(
Proper Setup Procedure (must follow this EXACTLY or it won't work):
1) IF YOU HAVE AN ULTRA: Obtain these three bins and put them on USB stick:
VIEWSAT_ULTRA_V0146.PGM ("factory" bin)
PFTAUSW-100322U.PGM (the "322" bin)
PFTAUSW-100320U.PGM (the "320" bin)
IF YOU HAVE AN ULTRA LITE: Same as above just the ones for the UL instead.
2) Connect the USB stick to the front USB port, fire up the STB
3) Go to menu "System Information" -> "Receiver Upgrade" -> "USB"
4) Navigate to the factory bin, select it, install
5) Wait for it to finish and reboot. Sometimes it will sit there with 0000
on the front panel, press the remote power button if so (it's in soft-off)
6) Go to menu "System Information" -> "Factory Default", enter PIN, say yes
7) Repeat step 3-5 but with the "322" bin instead
8) Connect serial. Fire up wfemu. Double check /dev/pts/ path and set it in
your SSSP client. Fire up the SSSP client. (use "screen" or two terms)
9) Go to menu "Installation" -> "Serial Setup" -> "Network S/W Upgrade" ->
"Network S/W Version" and verify it comes back with "wfemu v0.1b"
This verifies your serial connection and that wfemu is ready.
10) Observe the wfemu output and make sure it has sent the "CaID Map" packet
(it will continually do this every 5 seconds or so, and will also do it
following a "Connection Control" command from the VS)
11) Once you have seen the "Connection Control" packet from the VS and a few
of the "CaID Map" responses, leave wfemu running and continue at step 12
12) Repeat step 3-5 but with the "320" bin this time (yes, downgrade)
The "322" bin doesn't work with the real WF either so this is required.
The "320" bin doesn't accept the "CaID Map" packet which is why you must
install "322", feed it the "CaID Map", and then downgrade to "320"
13) Once you are back up with "320", set up your satellites and do an autoscan
14) Go to a channel you know your IKS provider handles, watch TV.
Proper Setup Procedure (must follow this EXACTLY or it won't work):
1) IF YOU HAVE AN ULTRA: Obtain these three bins and put them on USB stick:
VIEWSAT_ULTRA_V0146.PGM ("factory" bin)
PFTAUSW-100322U.PGM (the "322" bin)
PFTAUSW-100320U.PGM (the "320" bin)
IF YOU HAVE AN ULTRA LITE: Same as above just the ones for the UL instead.
2) Connect the USB stick to the front USB port, fire up the STB
3) Go to menu "System Information" -> "Receiver Upgrade" -> "USB"
4) Navigate to the factory bin, select it, install
5) Wait for it to finish and reboot. Sometimes it will sit there with 0000
on the front panel, press the remote power button if so (it's in soft-off)
6) Go to menu "System Information" -> "Factory Default", enter PIN, say yes
7) Repeat step 3-5 but with the "322" bin instead
8) Connect serial. Fire up wfemu. Double check /dev/pts/ path and set it in
your SSSP client. Fire up the SSSP client. (use "screen" or two terms)
9) Go to menu "Installation" -> "Serial Setup" -> "Network S/W Upgrade" ->
"Network S/W Version" and verify it comes back with "wfemu v0.1b"
This verifies your serial connection and that wfemu is ready.
10) Observe the wfemu output and make sure it has sent the "CaID Map" packet
(it will continually do this every 5 seconds or so, and will also do it
following a "Connection Control" command from the VS)
11) Once you have seen the "Connection Control" packet from the VS and a few
of the "CaID Map" responses, leave wfemu running and continue at step 12
12) Repeat step 3-5 but with the "320" bin this time (yes, downgrade)
The "322" bin doesn't work with the real WF either so this is required.
The "320" bin doesn't accept the "CaID Map" packet which is why you must
install "322", feed it the "CaID Map", and then downgrade to "320"
13) Once you are back up with "320", set up your satellites and do an autoscan
14) Go to a channel you know your IKS provider handles, watch TV.