2 severs are conflicting each other

[coyhunter]

I had to zero out port# on my beaver-north,,,,,,,,,,,it was causing continually freezing on my dish-net channels...they operate on a different server.............may shouldnt use two servers north and south???????? the north one works great when they are both connected though.............any advice??????

[Anubis]

I don't think it's the north conflicting per say but dn freezing period. This is from last night...http://www.satfix.net/showthread.php?120715-Beaver-tv-up-down/page25

[coyhunter]

the freezing was still on this AM.........WENT AWAY when I zeroed out out beaver north

[satcom4]

the freezing was still on this AM.........WENT AWAY when I zeroed out out beaver north

i have found best way thou not convenient to stop this is to just change the port on the one you not watching to "00" so it does not connect and when ready to just put it in and change in the other so only one connects at a time.. Also depending on the receiver you are using even tho they can have more than one PS loaded they don't always work great with more than one saved and connecting at the same time...

[ftaalltheway]

i have found best way thou not convenient to stop this is to just change the port on the one you not watching to "00" so it does not connect and when ready to just put it in and change in the other so only one connects at a time.. Also depending on the receiver you are using even tho they can have more than one PS loaded they don't always work great with more than one saved and connecting at the same time...

this true but never worry about NOI no issues there,,,so im told :)

[coyhunter]

i have found best way thou not convenient to stop this is to just change the port on the one you not watching to "00" so it does not connect and when ready to just put it in and change in the other so only one connects at a time.. Also depending on the receiver you are using even tho they can have more than one PS loaded they don't always work great with more than one saved and connecting at the same time...

thats exactly what I did,,,,,,,,,0 for beaver port until I need it

[KIDWCKED]

Dosen't matter what the serv is..Some stbs don't work well with more than one application..Jmo......

[coyhunter]

Dosen't matter what the serv is..Some stbs don't work well with more than one application..Jmo......

I HAVE nano premium................although when on beaver ...it works fine with both servers on
only when I GO to DN i have shut down beaver

[KIDWCKED]

I HAVE nano premium................although when on beaver ...it works fine with both servers on
only when I GO to DN i have shut down beaver

There are stbs that can run 6 at the same time without any dns/ip issues...Jus switch back and forth...I wouldn't change port..To 0000's...

[coyhunter]

There are stbs that can run 6 at the same time without any dns/ip issues...Jus switch back and forth...I wouldn't change port..To 0000's...

how do you switch back and forth

[forzaazzurri]

how do you switch back and forth

Easier to use server name and then switch to IP address when you want to turn OFF a server just as long as your IP address is zero (0.0.0.0).

[Wolf]

I also have the Nano Premium and have had the same probs when you have 2 different servers in it will freeze and lock up continuously but take one out and it works great. I have tried different things with the reciever but unless the 2nd server is out you will still get lock up and freeze.
That's why I am looking for a new receiver that can handle the work but I must say this has been a great little receiver I bought it before they were even up and running and it has paid for itself over and over again and very easy to setup!

[ramrod]

There are stbs that can run 6 at the same time without any dns/ip issues...Jus switch back and forth...I wouldn't change port..To 0000's...

You're right KIDWCKED, i'm running 3 on my sv8000...no probs.

[coyhunter]

what brand do you recommend...........?????????

[syabus]

For those running Nano Premium, the best way is to put DN on Server 1 and BEV on Server 2. I have been running Nano since it came out without problem with P$ and do not require to zero the port. Switch around and see if that will works.