dead jynxbox

[hmendez787]

I was watching tv a few hours ago and the box shut down alone!! Now i plug te box and turn the back suitch to on and it does not do anything not even the red light :( i notice that i can hear a little sound inside

[bkr™]

Disconnect all cables, unplug for a few minutes, restore power w/ nothing connected and see if it boots up.

[hmendez787]

I will wait a few hours and try again. It was working great a few minutes ago..an the shut off and when i try to turn on the box on again the red light start blinking on and off but not not even the red light nothings happen

[hmendez787]

I power the box on without the module and it power on and works ok but when i insert the module again it does not power on not even the display

[Nostradamus]

well then it sounds like you need a new module but I have never heard of any of them going in that fashion, a lot of freezing or heat prior to its last hurragh is common but just up and stopping is not

[hmendez787]

Well when previosly when i change the channels sometimes the signal whent down to 23 % and a few seconds later whent up again to 85% that was happening since the first day that i use the box

[Nostradamus]

actually that is common and that is not a tuner isue but a failure for the box to switch sats as fast as it can change channels. Regardless if the box fires up normal without the module then it is the module itself. Have you tried just reseating the module back in. Possible it was just making a bad connection as well

[hmendez787]

I put the module in thr other slot and the box does not power on and i power the box on without the module and it works and display image on the tv and everything but when i plug the module the box do not do anything de display does not even show the red light thanks for trying to help me

[Nostradamus]

ok that pretty much confirms the module is fried. You need to get a new module and you should be good to go

[hmendez787]

Thanks the box have only 20 days of use i will try to contact the seller for warranty if he dont give me the warranty i will buy a new module!! Thanks for your help

[devil_inside]

He should honour it, they are much aware that there are issues with the module, mine was faulty and it was replaced without a hassle.

[bkr™]

Yes JB200 modules having high failure rate lately, last 2 I received for conversion to "B" for use in V1 box were defective in the package. Maybe they had a bad run of cheap chinese components to make these modules.

[hmendez787]

Yes only 20 days of use and boom a dead module :/ i send a email to the jynxbox team today and 2 days ago to the ebay seller and still waiting!!

[velocity9421]

the jynx team should respond. it may take 48 hours, but they will respond

[hmendez787]

The ebay seller just contact me I send to him the module and he would send a new one to me

[edrik]

in the 1970's , if it said made in japan, it meant it was junk. be great if china could get a clue there regarding their qc.
i am still watching this box, stories like this thread alarm me.

[hmendez787]

I bought a module today and installed it to the box and is working great again!!

[bobby]

Yes JB200 modules having high failure rate lately, last 2 I received for conversion to "B" for use in V1 box were defective in the package. Maybe they had a bad run of cheap chinese components to make these modules.
unless you need the jb200 module in a v1 for dual tuner purposes no need to convert to a "B", you can install the jb200 in slot #2 of a v1 jynx and it will work without issue

[bkr™]

unless you need the jb200 module in a v1 for dual tuner purposes no need to convert to a "B", you can install the jb200 in slot #2 of a v1 jynx and it will work without issue
Very true, I now always test in slot 2 in a V1 to make sure they are good before mod. Many people want dual tuner use here, they do not want to purchase new when these great receivers work, most just tired of DN ecms and wish alternate options.

[bkr™]

Well lost a V1 today, I am really upset, shut unit off, disconnected all, put on bench, opened up and removed JB200-B and DVBS2 modules, and installed a new JB200 in slot 2 for testing. Turned unit on and red light flashed 2 times then nothing. Shut down and removed module, tried power up, unit is dead. It fried something, these new modules are really junk, this is #3 in a row, never had one kill a box tho. Had to set up a different receiver to get tv and I do not like as well. I will have to wait for a few weeks to receive a new V2 here. Another RIP