Help set up BEV and Charlie

[xxcutive]

I an currently have Charlie(DN) 110 119 129 set up my DISH HD (dish 1000.2) with DPP 44 and power inserter. Now I have a Dish 500 with Twin Dual LNB for 82 and 91. I believe this LNB able to get 110 and 119 too. But right now I only use for to get 91 for BEV which is so easy to get signal on 91 to go to port 4 DPP 44 so I wonder if or how to get both 82 also and what other device do I need to set up. any help with diagram is appreciated. The other question is when I replace the Dish 500 with DP dual LNB to a single LNB with elliptical dish to get 92 so easy to get signal but hard to get 82 because its has more HD.....
Regards

[KIDWCKED]

Far as I think you can take one output from each DP44 (two outputs) and put them into a 22khz switch
then output to the receiver. Shud works with SW21.Hopefully Terryl chimes in...He is a pro at this..;-]

[Terryl]

Dish DP equipment does not like to play well with NON-dish DP equipment, you can try the 22 KHz switch idea as Kidwicked mentioned and see if it works

It would be a DPP44 switch for 110/119/129 on one setup.
And a second DPP44 switch for the DP duals used for 82 and 91 on the other setup.

You then run the #2 receiver outputs of the DPP44's to a 22 KHz switch, the output of this switch to the receiver.

Switching would be:


119W= Diseqc #1, 22 KHz OFF
110W= Diseqc #2, 22 KHz OFF
129W= Diseqc #3, 22 KHz OFF

91W= Diseqc #1, 22 KHz ON
82W= Diseqc #2, 22 KHz ON

Some have reported this to work, others have problems.

Be sure to ground all switches to an outdoor metal cold water pipe, a ground rod, or the house AC service ground outside the building, this ground should be as short as possible, and you should use #12 gauge or larger copper wire with a green jacket.

If this does not work out as planned, or you experience switching problems, then you will have to change to all standard LNBs, one for each satellite and go with a 2.0 8x1 Diseqc switch.

[xxcutive]

Thx to both of you for the info but from Kidwicked say I only need a SW21 switch but not sure how the connection goes and Terryl post say I need another DDP 44 to a SW 21. Right now my connection look like this.
Dish HD (1000.2)
119 ------> 1 of the DPP 44
110 ------> 2 of the DPP 44
129 ------> 3 of the DPP 44
Dish 500 with Twin Dual LNB
but right now I can only chose either 82 or 91 so I pick 91 because more easy to get signel on 91
91 ------> 4 of the DPP 44
other side of the DPP where number 1 to power inserter and the other side of the inserter say to Receiver My Sonicview 8000 HD and works really good although 91 doesn't open up a lot of channels right now and I know that, so if you have diagram my more easier to understand.
Thx a bunch
ps if this work I tested on my Jynxbox too 0-)

[xxcutive]

I have a dish 500 with a single twin LNB. I already have a dish Turo HD which is similar to Dish 1000.2. Right now my set up following like this with DPP 44 and power inserter.
Dish TUrbo HD set up
119 to port 1 DDP 44
119 to port 2 DDP 44
129 to port 3 DDP 44

Dish 500 with single Twin LNB
I am able to get 91 on Bev but so hard to get 82 when I test on a separate on a regular Disq switch so I use the 91 Bev to port 4 of the DPP 44. My question is how to get both 82 and 91 and what kind of switch so I need and how to set it up. I have ppl suggest that I need another DDP 44 and also a sw 21 or ecoda 22 KHZ. If any one have a similar set up plz help me and others if there is diagram is a great asset to understand.
Thank you in advance.