I-Hub

[nighthawk1969]

I have one of the first I-hubs that came out right after the big ecm. Can I still use it? What would I need for this to work?

[Dish expert]

Yes, you can use it but you need to update it to 4.12.

[nighthawk1969]

That's good news. Thanks. How do I go about getting codes for the I-hub?

[Dish expert]

you will need a private $erver to get scramble channel, first you need to check what version file is on your stb and on the ihub.

[csavoia]

I have also not used mine in a long while? what do I need to run it? I already have a few pay servers but I haven't set it up in so long I have no clue what I need to do to have the bev server and dn server running together. any help would be awesome.

[Sp0iler]

No way to have them run together with SV.
One server at a time and you have to manually chose which one.

Look here for updating:
http://www.satfix.net/showthread.php?119735-Easy-I-hub-upgrade-and-V82-fix

Good luck,
Sp0iler

[csavoia]

my software says version 4.17 on it but it keeps asking for new software. where can I find this version 2.2 on my stb. where would it show that. thanks for any and all help

[csavoia]

well spoiler I followed the directions for the wiz to a TG and now when I put the new svlan software on I don't even have a menu for ip config so I cant even put in info on my receiver. now what the hell do I do???

[csavoia]

oh yeah and the wizhub no longer finds the box. yippee for me. thanks for all your help spoiler. unbelievable

[Sp0iler]

I'll bet you failed to hook straight into your lan port and you tried it through your network didn't you ?
Whatever you did, you most likely bricked the dongle.
Go back to the updating link and follow the instructions again.
There's a good chance your now at version 82 or 82.9.

[csavoia]

How do I do it straight through a LAN port? I have a bridge. So I should have brought the receiver ino my office and hooked it up to my receiver through an own port on my router? I don't understand. I tred it again and wiz hub can't find the receiver. How o I backtrack it?

I don't understand what you mean put it in the LAN port on computer. I only have one port and that's where the Internet goes in. Is that where the line is supposed to go?

If I have bricked the dongle then I am screwed. I don't have money tobuy another dongle.

[Sp0iler]

Your dongle is fixable.
If your hardwired from your computer to router, remove that connection (for now) and plug in the dongle instead (into the computer). It's the only hole in your computer the data cable will plug into.
Use Wiz to locate the dongle after your hardwired from the lan (local area network) port.

[skinnerboy45]

ihub 412 shows your good to go with the new up date files put new file on riever if I hub lates file if wizboard then its the chuck file or windows emelater file put on riever do not have hub connected till files on riever then shut of riever at bach hook up ihub or wiz board turn on switch an see it connected an watch tv if your server setting are in an scan right

[csavoia]

No offense skinner boy but I have no clue what you are saying. I will take the receiver ndrun it through my LAN port on the pc. But what the hell do I do after that to get the network menu back? Spoiler please tell me what to do when I run the wizard. Do I start over from scratch as if I had one nothing??

[csavoia]

Tried what you said and ran the wizard with the dongle connected straight to my lan port on the pc and it cannot locate it. What does this mean. is there hope for it. I don't understand why it does not find it but it doesn't. I have pinged the actual ip address and it does ping. I am at my wits end. please someone friggin help me.