View Full Version : Help with Nanosat Premium Satelite setup
Hello all
I am trying to setup a satellite Dish
If anyone has any input that would be greatly appreciated
I thought I have it aimed but see my settings below
Not sure what the heck is going on
NANOSAT Premium receiver
I am using a Standard Bell Dish with the Dual LNB Bracket for 91 and 82
NIMIQ 1
Disseqc None
Duseqc 1.1 None
TP Frequency 12297
LNB 11250
22 KHZ off
Muilti Dish Off
Search options All
LNB Power ON
Signal 90% Quality 0%
Can you please help direct me in the right direction
hutch
12-27-2013, 03:12 PM
are you sure the LNB you connected is for 91 not 82??? 82 is HD & will not give you Q on the premium...you can also try a different TP... check connections...LNB etc... I take it you are in the footprint(somewhere in Canada)?
dishuser
12-27-2013, 03:14 PM
are you sure the LNB you connected is for 91 not 82??? 82 is HD & will not give you Q on the premium...you can also try a different TP... check connections...LNB etc... I take it you are in the footprint(somewhere in Canada)?
not all of 82 is hd
Its a single dish with the single arm and dual bracket for 91 and 82
They then go to a box (Excuse the terminology) with a single coax to the receiver.
And yes location is correct
Can anyone send there settings for a similar setup
DMC
dishuser
12-27-2013, 03:38 PM
Its a single dish with the single arm and dual bracket for 91 and 82
They then go to a box (Excuse the terminology) with a single coax to the receiver.
And yes location is correct
Can anyone send there settings for a similar setup
DMCis it using an sw21 switch?
if so then you need to select that in setup
Its a 4x1 diseqc switch that the two lnbs are hooked into and then single coax to the nanosat premium
dishuser
12-27-2013, 04:26 PM
use port 1 for 91 and port 2 for 82 under diseqc
filippo
12-27-2013, 04:30 PM
in youre set up you have to assign satelite to disques@ sat 91-disq.1 and sat 82 disq.2 make sure that youre 2 cables are corectly assigned in youre disq.
I don't recall doing that when I was pointed to 110 and 119
But will do that and let you know
Also does the Nanosat premium need any updates
As I also had did a factory default before this and it didn't come back like it had prior but will do the diseqc setup first
Thanks for your help and talk to you soon
DMC
filippo
12-27-2013, 06:02 PM
I don't recall doing that when I was pointed to 110 and 119
But will do that and let you know
Also does the Nanosat premium need any updates
As I also had did a factory default before this and it didn't come back like it had prior but will do the diseqc setup first
Thanks for your help and talk to you soon
DMC
go to nanosat fles and instal the latest file for youre box is it nanosat premium or premium se
Nanosat premium
So which files
And do you have any directions on installing the files via the front USB or the back one?
dishuser
12-28-2013, 01:23 AM
Nanosat premium
So which files
And do you have any directions on installing the files via the front USB or the back one?load 1.12 with front port
I have loaded the 9.15 and the new sky 1.12
And I have taken the Diseqc switch out of the equation and just have only one lnb for 91
At the moment my settings are TP freq at 12224 and lnb at 11250 and have 95% signal and no quality.
I am going out to fine tune the sat to see if that helps but I am open to all suggestions on what to do next
DMC
torpainter
01-02-2014, 06:21 PM
Sounds like it just needs aiming properly
Check dishpointer dot com
I have 95% signal and quality but no sound or picture, and have scanned all channels and they loaded
My info is in the Net Application and have a good internet connection to my router
And the lights are on at the network cable
I am on 12224 and tp frequency is 11250
I am only on 91 at this time
Frustrating
Powered by vBulletin® Version 4.2.5 Copyright © 2024 vBulletin Solutions Inc. All rights reserved.