Bricked at 82

[bearbait]

well afer 2 days and nights I guess it's time to ask for help. I think my problem is I just can't get it to communicate.I went into internet protocol and changed everything as suggested, I have it hooked up directly to the computer, my IP adress is 192.168.11.2
sub is the usual
gateway is 192.168.11.1
serverIP is 192.168.11.3 as seen by wiznet. I have no more ideas and my eyes are bleeding I've read so much. Any help is much appreciated. Sometimes it goes to load the file then bums out. I have all the 82 files but it just won't write any of them. If I had more hair I'd pull it out.

[Sp0iler]

Confirm you have the current Svlan file in your box.
While hooked directly to your computer lan port,
Use Wiz and search for your dongle.
Set to "Static".
Go to "Local Ip" and enter -192.168.11.15
Enter your "Subnet"- 255.255.255.0
Go to your "Local Gateway" and enter 192.168.11.1
For "Server ip" enter- 0.0.0.0
For both ports enter- 0
Operation mode to- "Mixed"
"Use Dns"- UNchecked

Hit "Settings" to save the change and then reboot the box.
After it restarts, Search again with Wiz for your dongle.
Did the settings you entered save okay to the dongle ?
If yes, try loading the Svlan 43 file.
If it loads okay, You should now be at version 4.3.
Shut everything down.Reconnect the dongle into your network as normal and reboot the box.
If all has gone well you will see the "Updating" message shortly after rebooting.
Let us know how you make out and good luck,
Sp0iler

[bearbait]

Confirm you have the current Svlan file in your box.
While hooked directly to your computer lan port,
Use Wiz and search for your dongle.
Set to "Static".
Go to "Local Ip" and enter -192.168.11.15
Enter your "Subnet"- 255.255.255.0
Go to your "Local Gateway" and enter 192.168.11.1
For "Server ip" enter- 0.0.0.0
For both ports enter- 0
Operation mode to- "Mixed"
"Use Dns"- UNchecked

Hit "Settings" to save the change and then reboot the box.
After it restarts, Search again with Wiz for your dongle.
Did the settings you entered save okay to the dongle ?
If yes, try loading the Svlan 43 file.
If it loads okay, You should now be at version 4.3.
Shut everything down.Reconnect the dongle into your network as normal and reboot the box.
If all has gone well you will see the "Updating" message shortly after rebooting.
Let us know how you make out and good luck,
Sp0iler

Thanks SpOiler but still no go. It keeps the settings but fails to load

[Sp0iler]

Any error messages ?
"Not in the same sub-set" error perhaps ?
Maybe "Invalid parameter" ?
Anything other than "Failed to upload" ?
Are you familiar with the program "TeamViewer" ?
I would be willing to take a look for you if you like.

[Sp0iler]

C/P from another one of my posts:

Not sure of your windows version but try this:
Make sure your hardwired from your lan port...

Right click on the Network icon on your desktop and chose "properties".
Choose "change adapter settings".
Double click on "local area connection".
Locate "Internet Protocol Version 4 (TCP/IPv4)" and double click on it.
Choose "Use the following ip address"
For "IP address", enter your default gateway but make the last number .15 (ex:192.168.0.15)
"Subnet mask" is the usual 255.255.255.0
"Default gateway" is your default gateway... duh...(ex:192.168.0.1)
Dont worry about entering anything for "DNS server" and click "ok" to exit out.
Try again to load the file.
Post your results.

End C/P

Good luck,
Sp0iler

[bearbait]

Any error messages ?
"Not in the same sub-set" error perhaps ?
Maybe "Invalid parameter" ?
Anything other than "Failed to upload" ?
Are you familiar with the program "TeamViewer" ?
I would be willing to take a look for you if you like.

Just "Failed to upload"

I never heard of TeamViewer but I'll give anything a try at this point
Should these Wiz110sr's get this hot? I used to have the old Ihub but of course that was in a case but I didn't notice it getting hot

[bearbait]

C/P from another one of my posts:

Not sure of your windows version but try this:
Make sure your hardwired from your lan port...

Right click on the Network icon on your desktop and chose "properties".
Choose "change adapter settings".
Double click on "local area connection".
Locate "Internet Protocol Version 4 (TCP/IPv4)" and double click on it.
Choose "Use the following ip address"
For "IP address", enter your default gateway but make the last number .15 (ex:192.168.0.15)
"Subnet mask" is the usual 255.255.255.0
"Default gateway" is your default gateway... duh...(ex:192.168.0.1)
Dont worry about entering anything for "DNS server" and click "ok" to exit out.
Try again to load the file.
Post your results.

End C/P

Good luck,
Sp0iler

I gave this a try but it says 192.168.11.15 is unreachable
Thanks again for all the help

[bearbait]

Well I have it working. A big thanks to runamok for finally getting it going and also a big thanks to SpOiLer. Thanks to both for taking the time to help.

[runamok]

Well I have it working. A big thanks to runamok for finally getting it going and also a big thanks to SpOiLer. Thanks to both for taking the time to help.


Your welcome,there is no doubt spoiler would have got you going the same way.

[bearbait]

Your welcome,there is no doubt spoiler would have got you going the same way.

To that I have no doubt, thanks again

[bauzzoo]

you guys are great:yeaah:

[Sp0iler]

That's great news and glad you got it back to working.

Happy viewing,
Sp0iler

[bearbait]

That's great news and glad you got it back to working.

Happy viewing,
Sp0iler

Thanks for all the help.