Miissing channels

[roper7]

I have the Dreamlink HDMI SD I am missing 239 and the lower channls is there a chnnel list? or how can I get the rest of the channels.

[whoknows]

If you are missing the channels I would check my dish for alignment and then rescan should bring the listings to your box. Whether they are viewable would depend on what p$ you are using. Hope this helps.

[torpainter]

I have the Dreamlink HDMI SD I am missing 239 and the lower channls is there a chnnel list? or how can I get the rest of the channels.

post your hardware set-up and settings.

[roper7]

dreamlink sd hdmi dish 500 110/119
Latitude 2x.5100, Longitude xx,2188 (Location)
Elevation 43.4
Azimuth (true) 228.1
Azimuth(magn) 234.3
LNB Skew 40.4

[hedley]

please post your sat settings as they appear on your screen for each sat involved.

[roper7]

whats the meaning of P$ and I cannot get 239 or 138

[torpainter]

whats the meaning of P$ and I cannot get 239 or 138

you need to post your settings as asked

[roper7]

please post your sat settings as they appear on your screen for each sat involved.
Echostar 10/11 blue bar S 85% Q 97%
110
LNB Power On
LNB Type OCS-DP
LNB Frequency 11.250
LNB 22KHz Off
DISEQC SW 1.0 1
DISEQC SW 1.1 OFF
Legacy SW OFF


119.0W Echostar 14 S 28% Q 21%
LNB Power On
LNB Type OCS-DP
LNB Frequency 11.250
LNB 22KHz OFF
DISEQC SW 1.0 2
DISEQC SW 1.I OFF
Legacy SW OFF

[torpainter]

Echostar 10/11 blue bar S 85% Q 97%
110
LNB Power On
LNB Type OCS-DP
LNB Frequency 11.250
LNB 22KHz Off
DISEQC SW 1.0 1
DISEQC SW 1.1 OFF
Legacy SW OFF


119.0W Echostar 14 S 28% Q 21%
LNB Power On
LNB Type OCS-DP
LNB Frequency 11.250
LNB 22KHz OFF
DISEQC SW 1.0 2
DISEQC SW 1.I OFF
Legacy SW OFF
are you using a dishpro twin or two single lnbs with a switch? If you are using a twin lnb change 119 to port 1 and 110 to port 2

[roper7]

Iam using two single inbs with a switch

[torpainter]

Iam using two single inbs with a switch

bypass the switch and test each lnb directly to rcvr If both lnbs are fine your switch needs replacing
Always power off rcvr in back when connecting switches

[roper7]

bypass the switch and test each lnb directly to rcvr If both lnbs are fine your switch needs replacing
Always power off rcvr in back when connecting switches

I tested each LNB and all good and I have a new switch, went ahead and put CH LIST-C.LDB on system I have a Dreamlink SD (HDMI) Oct 23 2012 I am getting the missing channels but no picture Scramble Channel, what can be done, all other channels are good but the missing ones are bad ?

[dishuser]

I tested each LNB and all good and I have a new switch, went ahead and put CH LIST-C.LDB on system I have a Dreamlink SD (HDMI) Oct 23 2012 I am getting the missing channels but no picture Scramble Channel, what can be done, all other channels are good but the missing ones are bad ?
take it up with who you pay

[Mr Hanky]

You have two single lnbs???OCS-dp is for dishpro lnbs.

[dishuser]

You have two single lnbs???OCS-dp is for dishpro lnbs.

and your point is?

[Graeme33smith]

If ure missing channels - you could use SINGLE setting instead of OCS-DP and manually add a TP

So for eg.,lyngsat.com/packages/dish119.html

239 = TP 12472 L
So you add a TP 24600-12472 = 12128 V ( Which is R for Vertical and the opposite ) and scan

The above can be done for 119,110,118 and for 129 you use 25600 instead

[roper7]

bypass the switch and test each lnb directly to rcvr If both lnbs are fine your switch needs replacing
Always power off rcvr in back when connecting switches

Do you think maybe if I change the cables, what type of cable should I get.I have no idea what to do next.

[roper7]

Just wanted say thank you very much, I switched from OCS-DP to Single

[roper7]

I need some instruction on how to make the change to TP12472