v111 file discussion

[TurboPirate]

Hello gang, my friend wanted to say that with this file v111 he saw no improvement in the PVR and the Diseq. Who has noted something with this new file? Pros and Cons......friendly discussion or please don't say anything if it can not be said in a constructive way. TurboPirate

[TurboPirate]

WiFi disconnects every 3 to 5 minutes.

[Bob Loblaw]

I found that there was some improvement with the diseqc issues. Before this file I was unable to access 110 when there were other STBs using the system. Now I am able to address all the satellites regardless of what other STBs happen to be on the system.
I also found that scanning was somewhat better. I was able to scan each satellite individually and all channels were there, no need to scan TPs afterwards.
I will try with the wifi and let you know what I experience.

[TurboPirate]

That is one detail different about my friend's setup, he doesn't have a second receiver connected so I guess that is why he doesn't see any improvement on the diseq, thanks for sharing. TurboPirate

[Bob Loblaw]

WiFi isn't working for me

[TurboPirate]

WiFi isn't working for me
Those the receiver recognize the USB WiFi? with the WiFi setting's can you enter the wireless key of your Wireless Router?

[iq180]

WiFi isn't working for me
After you load new firmware you need to do a factory reset, if you don't the receiver want make any changes.

[Anubis]

After you load new firmware you need to do a factory reset, if you don't the receiver want make any changes.

Hehehe, believe me he knows what he is doing with this unit.;)

[TurboPirate]

After you load new firmware you need to do a factory reset, if you don't the receiver want make any changes.

Iq I completely forgot, check your PM.........................Many of today's receivers are very picky if no factory reset has being done it will not work, back in the day N2 I remember my SV4000, CW700 I never did a factory reset and those receivers worked perfect, but then again old receivers and this receivers are linux, TurboPirate

[Bob Loblaw]

Factory reset did nothing. The adapter connects to the network but there is no traffic passing through.

[greeny]

Have the file on my usb ,
unzipped it
plus to machine
upgrade by usb dribe but the file name or number did not come up???

your help is much appreciated

[TurboPirate]

Have the file on my usb ,
unzipped it
plus to machine
upgrade by usb dribe but the file name or number did not come up???

your help is much appreciated
If to installed the v111 file now you need to do factory reset, then check menu system info and you'll see the file number..

[Anubis]

Have the file on my usb ,
unzipped it
plus to machine
upgrade by usb dribe but the file name or number did not come up???

your help is much appreciated
After you unzip the file you only put the unzipped portion on the usb stick.

[iq180]

I think you need to load file v036 first then do a factory reset then load v111 then do another factory reset.
From what I remember the v111 want load on a receiver that only has the factory file.

[greeny]

no no its misunderstood..
i was saying i was able to upgrade the file
it said the file was unrecornizable

[greeny]

yes that was what i did
but the machine does not reconize the file

[greeny]

can you post v036 please
i am having trouble finding it

THANKS

[iq180]

no no its misunderstood..
i was saying i was able to upgrade the file
it said the file was unrecornizable
You seem to be very new to this, is your receiver an ultra lite, if so read post #14, if not post what receiver you have.

[iq180]

The v036 file is in the jynxbox file section.

[sassy1]

did the install, works fine all channels are working fine, only problem i have is the epg will not populate, did the factory resets as required.
help would be appreciated
thanks

[iq180]

did the install, works fine all channels are working fine, only problem i have is the epg will not populate, did the factory resets as required.
help would be appreciated
thanks
First thing, you need to set the time, then you need to put the receiver on CH 200 for 10 min, if you want more than 2 HRs
of epg you need to put a small USB drive in the receiver, 1/2 GB usb is all you need.

[sassy1]

First thing, you need to set the time, then you need to put the receiver on CH 200 for 10 min, if you want more than 2 HRs
of epg you need to put a small USB drive in the receiver, 1/2 GB usb is all you need.

I am running north only so 200 is actually 400 will this work, i know with v36 if you didn't use 24 hr clock there was no guide?

thanks

[iq180]

I am running north only so 200 is actually 400 will this work, i know with v36 if you didn't use 24 hr clock there was no guide?

thanks
Press the guide button then press the yellow button and you will get a list of epg CHs, just put it on one of the CHs in the list
and let it sit for about 10 min.

[sassy1]

So tried all the info you gave me and still no guide, any more ideas i can try, ? would reloading the v111 make any sense at this time?or another factory default ?

thanks

[whoknows]

If you had the wrong lnb type you would be able scan for channels and also view channels but would not have a guide. Try changing l n b type and do a hard boot. Put it on 1500 and wait. good luck

[sassy1]

I had this setup for over 1 year now and always had a guide, since putting v111 on no guide..will try the lnb change and see what happens

thanks

So rescaned, scanned channels work till the system puts the 2 infront of the north channel number, then nothing. (eg 0400 works, but 2400 gets no info)

anybody else using north only, having this problem with a jbox ultra lite HD

thanks

didi a re scan of network only, this got rid of the 2 in front of the channel numbers and now works. I had previously reloaded my backup user database
and this was the problem all channels started with a 2..

thanks

[TurboPirate]

Try setting the receiver with your location, if your location is -4:00 or -4:30. TurboPirate

[TurboPirate]

I know its being 2 years but today I was testing the Lite and notice no audio response at all, tried different channels pressed the RED button to change audio and nothing happen, tried different remotes same thing, checked the INFO it has file 111, just for fun loaded the Lite with file 036 now the RED (audio) button the audio window appears on TV and can change audio, something was forgotten on file 111, it works great but no audio change can be performed. TP