Pinwhell pro with Bev

[macuser33]

I know for 100 percent the 2 server's that work with Bev and I get no picture at all..Is there a problem with Bev with this unit???Is there something I am missing? Like I said server is fine no problem there ant all...Please help..Thank you as always..And Q 98% S 85% so the problem is not there..

[holly2012]

No the pinwheel works fine with North are you using it hard wired or wireless it sound like your not connected to the server

[macuser33]

No the pinwheel works fine with North are you using it hard wired or wireless it sound like your not connected to the server

Hard wired.. I get sound on some channels but no picture..And Dn works great...Could it be a bad LNB??Thank you for your help..

[macuser33]

Hard wired.. I get sound on some channels but no picture..And Dn works great...Could it be a bad LNB??Thank you for your help..

Anybody have any idea??? I tried everything can not get picture on Bev..Some channels I get sound a lot really but no picture..I know 100% it is not the server or LNB as I changed it out..What gives???Please guys any advice will help me..I am willing to try anything at this point..Please help..

[sg2100]

Anybody have any idea??? I tried everything can not get picture on Bev..Some channels I get sound a lot really but no picture..I know 100% it is not the server or LNB as I changed it out..What gives???Please guys any advice will help me..I am willing to try anything at this point..Please help..

Did you check your server page and made sure you selected newcamd_nim when you setup bev,just a thought i have done that before

[benfica]

With pwheel u get 2 places to add server info my friend ...please check that !

[macuser33]

Did you check your server page and made sure you selected newcamd_nim when you setup bev,just a thought i have done that before

Thank you Thank you Thank you...I never new that..It worked..You guys are the best...Can not thank you enough..I was going crazy trying to figure this out..You made my day.....Thanks again..

[macuser33]

Witch one is more west 91 or 82?? I can lock in 91 but not 82..And with this pinwheel can you use a 22hz switch in one port ? because 119 is port A 110 is port B 129 is port C and right now 91 is port C..Does 82 need to be more higher up than 91 or 91 need to be higher up than 82? Thanks again..

[holly2012]

From behind the dish 82 is a little to the right of 91 and slightly lower you best set your skew to 90 degrees and lock onto 82 first then skew the dish to the right just slightly for 91 and yes you can use a 22KHz switch

[macuser33]

From behind the dish 82 is a little to the right of 91 and slightly lower you best set your skew to 90 degrees and lock onto 82 first then skew the dish to the right just slightly for 91 and yes you can use a 22KHz switch

So I take it a sat with a poor man's bracket will not work for 91 and 82? since you can not skew it..

[whoknows]

Sure it will work. Here is an example of 119/110 which has the same spacing as 91/82.


http://www.ecoustics.com/electronics/forum/home-video/462888.jpg

[macuser33]

Sure it will work. Here is an example of 119/110 which has the same spacing as 91/82.


http://www.ecoustics.com/electronics/forum/home-video/462888.jpg

I have the one that is metal..and says 119 and 110. From behind the dish 110 is to the right is that the one I put LNB 82 on? I have and can get a lock on 91 but 82 I seem to not find it.. it shows a sat with q 80 s 99% but says unknown sat.. it will not lock 82.. I am in Canada so why I can not lock 82 is anybody's guess. Any idea's why?? Thank you so much for any help..

[holly2012]

What kind of receiver is it

[whoknows]

Yes the 110 l n b is for 82. Most tp are HD so you have to pick a sd transponder for alignment. Go into antenna settings and change satellite(right arrow) to 82. Then move down to tp frequency and right arrow again to 12428 or 12433 as they are sd transponders which you use for aligning dish. If you have a switch then to to disq parameter and change to a or b, or if you have a 22khz switch change to on or off depending which side of the switch you have 82 plugged into. Now you should be able to adjust l n b slightly for quality. good luck

PS: don't forget to hit the green button and save once you get a lock on satellite

[macuser33]

Yes the 110 l n b is for 82. Most tp are HD so you have to pick a sd transponder for alignment. Go into antenna settings and change satellite(right arrow) to 82. Then move down to tp frequency and right arrow again to 12428 or 12433 as they are sd transponders which you use for aligning dish. If you have a switch then to to disq parameter and change to a or b, or if you have a 22khz switch change to on or off depending which side of the switch you have 82 plugged into. Now you should be able to adjust l n b slightly for quality. good luck

PS: don't forget to hit the green button and save once you get a lock on satellite


Is using the smaller DN dish ok?? because the bell one I have seen is bigger a little..So will it still work??Thank you so much..And this is for the pinwheel pro. and what TP to use for 91 and what tp for 82?

[holly2012]

12.224for both 82 and 91

[whoknows]

If you were getting rain fade then bigger dish is better. Depending on your location the smaller dish may work just fine. You ask for transponder for 82 which I already mentioned in my post. 91 it doesn't matter so don't change the frequency. And yes this information is for a pinwheel pro. good luck

[macuser33]

Ok I bought a real Bev dish with LNB for 91 and 82..I locked into 91 but can not get 82 at all..What do I need to do??I tried everything I can think of..Please idea'a..Need help worked on this for 3 days now..Thank you to everyone that helped me so far you been great..

[holly2012]

Like I said before set your dish skew to 90 degrees tighten it then scan for 82 lock onto 82 then just loosen the skew bolts and turn the dish slightly to the right from behind the dish till you lock onto 91 then double check 82 if you have to make the adjustments on the dish till you have the best S and Q you can get on both sats.thre could be something in the way of 82 as well Google this Site it will tell you if there is something blocking the signal dishpointer.com

[macuser33]

Like I said before set your dish skew to 90 degrees tighten it then scan for 82 lock onto 82 then just loosen the skew bolts and turn the dish slightly to the right from behind the dish till you lock onto 91 then double check 82 if you have to make the adjustments on the dish till you have the best S and Q you can get on both sats.thre could be something in the way of 82 as well Google this Site it will tell you if there is something blocking the signal dishpointer.com

91 is more west then 82 right??Thank you again for everything..

[macuser33]

Like I said before set your dish skew to 90 degrees tighten it then scan for 82 lock onto 82 then just loosen the skew bolts and turn the dish slightly to the right from behind the dish till you lock onto 91 then double check 82 if you have to make the adjustments on the dish till you have the best S and Q you can get on both sats.thre could be something in the way of 82 as well Google this Site it will tell you if there is something blocking the signal dishpointer.com

I finally found 82 but now can not lock on to 91.. I tried everything you said and more no luck..I give up..I either have bad luck or I am just dumb..I have installed sat's many times and never ran into something like this. Any more help I would welcome it big time.. what is the best TP to use for locking in 91? Thanks again..

[Bobburger]

What I experience with the pinwheel box is I got the 82 correctly and when I try to get the 91 it stay on 82 I move the transponder from another one sometime it will switch to 91 lock if not remove the power from the back and it will lock to 91 assuming that goto calculated 91 as been done.

[hedley]

I finally found 82 but now can not lock on to 91.. I tried everything you said and more no luck..I give up..I either have bad luck or I am just dumb..I have installed sat's many times and never ran into something like this. Any more help I would welcome it big time.. what is the best TP to use for locking in 91? Thanks again..
did you Plumb your mast?

[macuser33]

did you Plumb your mast?

Finally I get it..It did not like the 22hz switch I was using.. at all.Put new one on boom 91 and 82 S89 and Q 98 both..Thank you to everyone who helped me out you are great..