How to set up JynxBox Ultra HD v3 with 58W, 110W, 119W and 129W?

[gpo.valcer]

Hi all. I have had this system for about a year now, hadn't had any problems until I decided to upgrade the firmware to V251. Now I lost all my channels and can't find the configuration guide that told me what settings to use for each sat.
Please help.

[gpo.valcer]

I would if I had the settings to configure each one of the satellites. I have to set those values no matter what firmware I'm using. If someone could help wth those settings it would be greatly appreciated.
Thanks.

[hondoharry]

Been trying unsuccessfully to get 58W on a Skybox F3 and the settings may help me as well.

[diode]

Been trying unsuccessfully to get 58W on a Skybox F3 and the settings may help me as well.

Jynxbox will not blind scan this sat. Add these TP to the list on 58w . Menu, Installation, Manual Scan, Green Button to Add. Save Then scan Sat. The Oopenbox should be able to blind scan once you get locked onto one of these TP.
I did not include the HD TPs because they will not be useful.

11760 H 30000 QPSK
11800 H 30000 QPSK
11840,H,30000,5/6,DVB-S,QPSK
11960,H,30000,Auto,DVB-S,QPSK
11980,V,30000,Auto,DVB-S,QPSK
12000,H,30000,Auto,DVB-S,QPSK
12020,V,30000,Auto,DVB-S,QPSK
12040,H,30000,Auto,DVB-S,QPSK
12060,V,30000,Auto,DVB-S,QPSK
12080,H,30000,Auto,DVB-S,QPSK
12100,V,30000,Auto,DVB-S,QPSK
12120,H,30000,Auto,DVB-S,QPSK
12140,V,30000,Auto,DVB-S,QPSK
12160,H,30000,Auto,DVB-S,QPSK
12180,V,30000,Auto,DVB-S,QPSK

[diode]

By the way you do need a Standard or Universal LNB not a circular DSS LNB. You must also adjust the skew of the LNB for you location. Google "dish pointer" to find out your specific setting.

[hondoharry]

By the way you do need a Standard or Universal LNB not a circular DSS LNB. You must also adjust the skew of the LNB for you location. Google "dish pointer" to find out your specific setting.

I have 2 universal LNB's that work on Claro 125. One (generic) works at 9750/9600 and the other (Avenger) at 9750/10750. Seems strange they need different configurations for the same sat.

I tried both LNB's looking for 58W and was unsuccessful. What is the LNB setting for this sat with my 2 LNB's.

[diode]

I have 2 universal LNB's that work on Claro 125. One (generic) works at 9750/9600 and the other (Avenger) at 9750/10750. Seems strange they need different configurations for the same sat.

I tried both LNB's looking for 58W and was unsuccessful. What is the LNB setting for this sat with my 2 LNB's.

Most Universal LNBs should be set to Universal 9750-10600 on the jynxbox. The correct setting does depend on the actual LNB not the Satellite. Universal LNBs have two lofreq oscillators so that switch depending on the frequency of the TP. Make sure that you have your coax going to the correct tuner if you have a dual setup or you need to have a loop connector. For instance 125w would be on your DVB-S2 tuner while 58W could be on your jb200. 58W should work on either. 125 will only work on a DVB-s2. Make sure the word Universal is in front of your freq. selection. 22K will then turn blue and be set on auto. Try looking for tp 12180 at 30000 V QPSK in the manual scan section. If you see no signal... wait for about 30 sec. ... still no signal... exit out of the menu and then come back to it. For some reason the signal meters on jynxbox don't respond well.

[hondoharry]

Most Universal LNBs should be set to Universal 9750-10600 on the jynxbox. The correct setting does depend on the actual LNB not the Satellite. Universal LNBs have two lofreq oscillators so that switch depending on the frequency of the TP. Make sure that you have your coax going to the correct tuner if you have a dual setup or you need to have a loop connector. For instance 125w would be on your DVB-S2 tuner while 58W could be on your jb200. 58W should work on either. 125 will only work on a DVB-s2. Make sure the word Universal is in front of your freq. selection. 22K will then turn blue and be set on auto. Try looking for tp 12180 at 30000 V QPSK in the manual scan section. If you see no signal... wait for about 30 sec. ... still no signal... exit out of the menu and then come back to it. For some reason the signal meters on jynxbox don't respond well.

Actually I'm using a Skybox F3 with a DVB-S tuner. Will that work on Sky? What settings?

[diode]

The S10 works great so I would think that the F3 would work as well. Make sure your 22k switch is set to auto for the universal LNB.

Actually I'm using a Skybox F3 with a DVB-S tuner. Will that work on Sky? What settings?