Jynxbox set up help

[havenlyskyhigh]

Just got my box today, first I load clone safe file, JX_NA_Firmware_v239_dual - ORIGINAL CLONE SAFE FILE.
Next do I have to load All Chunks and Firmware of the V7 to my V4 stb?

This is just concerning my doing first step.

[Anubis]

You just need the V7 allchunk file.

[havenlyskyhigh]

Thank you

Anubis



Anubis

[havenlyskyhigh]

Why I can't connected to the sever here is the detail
model..... jynxbox V7
loader Version ........V 1.2.20
hardware version ....v 1.0.3
Data Version ..........v 1.0.1
Firmware................v 3.2.57
build date...............2013-9-3
Barcode..................jx44002274

Server setting
protocol NewCamd
Ip/ name 4.ro.....
port............35...
Id................same
pass............same
Deskey ......###########

[iq180]

Why I can't connected to the sever here is the detail
model..... jynxbox V7
loader Version ........V 1.2.20
hardware version ....v 1.0.3
Data Version ..........v 1.0.1
Firmware................v 3.2.57
build date...............2013-9-3
Barcode..................jx44002274

Server setting
protocol NewCamd
Ip/ name 4.ro.....
port............35...
Id................same
pass............same
Deskey ......###########
Are you using wifi or hard wire internet.

[Anubis]

Why I can't connected to the sever here is the detail
model..... jynxbox V7
loader Version ........V 1.2.20
hardware version ....v 1.0.3
Data Version ..........v 1.0.1
Firmware................v 3.2.57
build date...............2013-9-3
Barcode..................jx44002274

Server setting
protocol NewCamd
Ip/ name 4.ro.....
port............35...
Id................same
pass............same
Deskey ......###########

Did you hard boot from back switch after inputting everything?

[havenlyskyhigh]

I used Wifi for now and I did a few times factory off switch from the back also.

I had tried a couples of my codes still no connected. And doing around setup it look everything ok. But one thing problem
was the sever I can't figure out.

[havenlyskyhigh]

Are you using wifi or hard wire internet.

I used wifi for now is that the problem?

[Anubis]

Try it hard wired. It is more reliable especially for a first run.

[havenlyskyhigh]

After work I hook up to hard wired, but it still No sever is connected is it rocket down or something wrong with firm wares I load?

If this firmware software problem, can I reflash allchunk bin v7 over it. Is it Ok or not?

Just a concern the wares.

[iq180]

After work I hook up to hard wired, but it still No sever is connected is it rocket down or something wrong with firm wares I load?

If this firmware software problem, can I reflash allchunk bin v7 over it. Is it Ok or not?

Just a concern the wares.
First go back and check all your server settings, next, menu/ tools/ wifi/ turn off wifi/ then exit and go to network local settings/
turn off DHCP and set all fields to all 0000000 then apply then do a hard boot with the power switch/ then go back and turn DHCP
back on then apply then do another hard boot.

[havenlyskyhigh]

I follow all your steps but it still nothing change at all. Any problem that I mention at # 10?
This problem I been fixing all day but nothing change.
Any idea that you can figure out Iq180

[Nostradamus]

take a look at the back of the receiver and see if you see activity lights flashing next to the LAN port

[havenlyskyhigh]

No activity Nostradamus, I then load usb to factory setting and now it got no way out seem I need to run rs 232 cable
resetting to original factory.
Where can I find step by step instruction how to back to factory setting?
I seen somewhere, but been looking a few days b4 I got this happen. what a screw up withh this box with usb factory 8 file.

Now I need this box bring to life, I need someone give me direction to get this box back to normal.
And thank you for all head up with my problem.

[iq180]

No activity Nostradamus, I then load usb to factory setting and now it got no way out seem I need to run rs 232 cable
resetting to original factory.
Where can I find step by step instruction how to back to factory setting?
I seen somewhere, but been looking a few days b4 I got this happen. what a screw up withh this box with usb factory 8 file.

Now I need this box bring to life, I need someone give me direction to get this box back to normal.
And thank you for all head up with my problem.
Try a factory reset first, if it's a problem with the software, just reload it with usb, no need to use the loader & loader cable.

[havenlyskyhigh]

What a screw up,
since I load factory v8 file with usb now the stb has no step for me to work on it stuck NO CH.
I can't used none of the button remote or other it not working no more.

[baseman]

reading that you have a V4...so has this box worked before? Did you get flashing lights working at the back where the network cable plugs in, if not you will get nothing (1 light flashes and the other is solid on).
If all is working you should have tv

[iq180]

Did you load any firmware other than V7 allchunk and V8 file, if not then you should be able to recover it with the loader and loader cable.
You can find the loader in the jynxbox file section.

[havenlyskyhigh]

Did you load any firmware other than V7 allchunk and V8 file, if not then you should be able to recover it with the loader and loader cable.
You can find the loader in the jynxbox file section.

Nothing else just V7 allchunk and V8 file, but right now I had no picture on TV and remote not work either.
I tried to load but it won't connected to port of stb it said { Target not connect or target is error status!} I ran from usb laptop with rs 232 to pansat serial rs 232 cable and it not contact.

Why is not contacted through the stb junbox?

[havenlyskyhigh]

reading that you have a V4...so has this box worked before? Did you get flashing lights working at the back where the network cable plugs in, if not you will get nothing (1 light flashes and the other is solid on).
If all is working you should have tv

To my knowledge in my area I got one open Wifi connected to stb no connection, after work I connect to my end using both different router { Wifi +hardwire} is not connected either. So that Y, I made up my mind using usb flash factory file and end up 'NO CH' on jungbox led.

[iq180]

To my knowledge in my area I got one open Wifi connected to stb no connection, after work I connect to my end using both different router { Wifi +hardwire} is not connected either. So that Y, I made up my mind using usb flash factory file and end up 'NO CH' on jungbox led.
Will the remote turn the box off & on, if it will and you have nothing on the TV, you have the wrong format, press the aspect button
on the remote, give it about 20 sec, each time you do this it will change the format and it could take up to 5 times to get the right
format.

[havenlyskyhigh]

The remote turn the box off and on but still no change or either no picture when I follow your step the screen dark blank.
On a screen led it still display no CH with blue lite. I think this nothing to do with the format tv screen it cause the factory software
won't mate with the usb installed.

[iq180]

Try the RCA cables, remember to chang the tv to RCA input.

[havenlyskyhigh]

Thanks Iq180 I never think of RCA input this work on THE NO CH.. always using HDMI,
and I posted some info. the NO CH.. problem had these headage also.

Thanks for all of you head up my stb even.

[havenlyskyhigh]

Now I'm back at square ONE again and still no SEVER CONNECTED.

Since no CH. or usb factory setting, I had used Rs 232 null cable loading V 8file more than 5 times to STB plus HDMI do nothing
dark screen. Thanks Iq189 your RCA Plugs start from scratch.

First I did Iq180 allchunk V7 Jynxbox step everything going good and well done.
Second factory reset off switch at the back than TOOL doing all the SEVER SETTING Id, password and DES key Exit 2 times factory
setting off back switch. Turn back on scan 1, 110 SAT nothing than went check the SEVER, No sever is connected.

I got 3 codes none of those had the SEVER connected check all hardwire at router lite and lite blinking and still no sever connect
to STB. Anything I missing our?

[iq180]

Turn off your jynxbox then turn off your router & modem, then turn on the router & modem, give them time to reboot then turn on the jynxbox, when you turn on the jynxbox it will not log on to the server at first, it will say failed, then you will see S&Q at the bottom of the TV screen, then it will connect if you have the server setup.

[havenlyskyhigh]

I did that previous with hardwire but it still do nothing. Now I started all everything off then on modem & router after I got internet
through my laptop then Jynxbox turn on and it still nothing change.

You said at the bottom of TV it has S&Q but on my bottom TV it has SIGNAL only. And right I used Wifi with Jynxbox still nothing
happen.

[iq180]

Are you using NewCamd or CcCam, I would use NewCamd, after you setup your server remember to Apply or it want work.

[havenlyskyhigh]

Have to be Newcamd, Cccam no Des keys to fill in and is not different from my Nano2 it just model and name.
I never had any problem since I'm with FTA 10years ago only this box set me in a Junkbox in a few days working on it and still
won't solved the problem.

[havenlyskyhigh]

My sever is not connecting is that relate with some router/modem set up?
This is what I concerned the cause the STB not matching with the connector some how.

[Arcange]

No - on remote
.. Only ? For caracteres ... I need - for put m'y password
. how make this please