Jynxbox V3 not accepting bin 243

[ftafever2015]

A V3 Jynxbox has a V2 Bin with no wifi feature. I am trying putting bin V243, but it is not accepted by the stb. No message given while installing new bin. Any thing wrong I may be doing? Please advise. Thanks
Using pen drive to flash new bin.

[ftafever2015]

Tried also bin 239 without success.

[iq180]

Tried also bin 239 without success.
Did you do a factory reset after you loaded the bin file, if not it want apply.

[ftafever2015]

Did you do a factory reset after you loaded the bin file, if not it want apply.

Yes I did, and have gone thru this process more than 5 times.
5 factory resets before and after, but nothing...oh, and thanks for your reply...

Note: also tried turning off from back switch...

[iq180]

Yes I did, and have gone thru this process more than 5 times.
5 factory resets before and after, but nothing...oh, and thanks for your reply...

Note: also tried turning off from back switch...
Go to menu/Tools/System Information/ and see what firmware you have on it now.

[ftafever2015]

Go to menu/Tools/System Information/ and see what firmware you have on it now.

It has V 1.2.34
This is full info. On System Informstion page :

Model Jynxbox V2
Loader Version. V 1.2.20
Hardware Version. V 1.0.3
Database Version. V 1.0.1
Firmware Version. V 1.2.34
Build Date. 2012-12-6
Barcode. JX44002274
RF Slot1. JB200
RF Slot 2. NULL
Stb is Ultra HD V3

[saggy]

did you extract bin also I think 243 is a clone crusher will brick receiver if clone try a different usb use 239 clone safe

[ftafever2015]

Can you please send me that bin? Thanks

[monchino]

use cable rs232, factory and the fix you want

[ftafever2015]

Yes. Rar bin extracted

[iq180]

Why don't you just load the allchunk file for the V7 and be done with it,jmo.

[saggy]

listen to iq180 he knows his crap also all info under jynbox files and discussion your usb might be bad does it light up when put in jynx if not then load with cable and loader

[ftafever2015]

Why don't you just load the allchunk file for the V7 and be done with it,jmo.

That sounds good....can you post that file link for me? Thanks

[Fibroso]

That sounds good....can you post that file link for me? Thanks

Everything is posted, need to look for it.

[Anubis]

That sounds good....can you post that file link for me? Thanks

Here you go....http://www.satfix.net/showthread.php?167574-JynxBox-Ultra-V7-2-57-DUMP

[iq180]

That sounds good....can you post that file link for me? Thanks
Get the allchunk and unzip it or unrar it, then you need to chang the file EXT from .abs to .bin, it should look like this.
allchunk.bin
Now in the receiver upgrade menu select allflash and load it.

[ftafever2015]

ready to flash via RS232. downloaded Loader, unzipped it, but file "upload.ini" is missing.
have searched for it with no success. Where is it? Please
Thanks

[iq180]

ready to flash via RS232. downloaded Loader, unzipped it, but file "upload.ini" is missing.

have searched for it with no success. Where is it? PleaseThanks

What file are you trying to load & why do you need to use the loader.

[ftafever2015]

Why don't you just load the allchunk file for the V7 and be done with it,jmo.
This one, recommended by you, sir.

[ftafever2015]

What file are you trying to load & why do you need to use the loader.



Default JynxBox Ultra V7 2.57 DUMP
DUMP of All Chunks and Firmware of the V7, for V7 recovery and for those that got the V7 brand new with "Factory File only, File must be loaded with Serial Cable ONLY."
Attached Files Attached Files
File Type: rar All Chunks&Firmware-v7.rar (3.01 MB, N/A views)

[Fibroso]

This one..... http://www.satfix.net/showthread.php?167574-JynxBox-Ultra-V7-2-57-DUMP


There's 2 files , all chunk.abs and firmware.bin
What are you doing?

[ftafever2015]

Just tried to load the Chunk....with USB, but nothing happened.

[ftafever2015]

Ok...the chunk.abs renamed to chunk.bin, then loaded. The Firmware. Bin file gives Invalid File massage. Do not know why.upgrade Mode at All Flash. Then Factory reset....nothing happened. Same old bin v1.2.3.4 and v2 at System Information...

[Fibroso]

Leave the file how it is and use the loader. Use chunk for the chunk file and firmware for the other.

[iq180]

Ok...the chunk.abs renamed to chunk.bin, then loaded. The Firmware. Bin file gives Invalid File massage. Do not know why.upgrade Mode at All Flash. Then Factory reset....nothing happened. Same old bin v1.2.3.4 and v2 at System Information...
You need to select allflash in the upgrade menu of the receiver.
if that don't work then you have loaded a clone kill file and the only way to recover it is with the loader and factory file, and that
mite not work.

[ftafever2015]

Fibroso: . Use chunk for the chunk file and firmware for the other. Do not understand this statement. Can you be more specific ? Thanks.....in addition, the loader does not have the "upload.ini" file. How Can I get it?

[iq180]

Fibroso: . Use chunk for the chunk file and firmware for the other. Do not understand this statement. Can you be more specific ? Thanks.....in addition, the loader does not have the "upload.ini" file. How Can I get it?
Put the allchunk on the same usb as the loader, after the loader is conected with the receiver you will have an option to look for files
select the usb then the allchunk file.

[ftafever2015]

Ok...I understand I still need to go via RS232 cable. Am I correct?