v2 with no signal 3 birds with and without power inserter dpplus

[lalord69]

i have a v2 with loader 1.2.20/firmware 1.2.43/ build date 2013-8-13 and a dpplus with 3 lnbs(they have 3 outputs and 1 input, black writing)

I cannot get signal no matter what i do!

The dish and lnbs works because i have a freesat hd running without any problems or issues.

i tried the lnbs straight to the box and nothing.

I tried a power inserter dpp44 and nothing. I tried the dpp44 with a line to the lnbs by itself then a second line to the jynx and nothing.

I also tried the jynx with the power inserter "inline" and nothing.

I changed all the settings in the box and nothing.

I also tried a 4x1 switch and could not get signal.

i moved the jb200 to the other slot and nothing.

I also reseted the box and nothing.

I know the box and jb200 works because i tested it with a dual lnb dpplus and i can get signal, just not with my dish!

I am lost, i need help please!!!

[iq180]

i have a v2 with loader 1.2.20/firmware 1.2.43/ build date 2013-8-13 and a dpplus with 3 lnbs(they have 3 outputs and 1 input, black writing)

I cannot get signal no matter what i do!

The dish and lnbs works because i have a freesat hd running without any problems or issues.

i tried the lnbs straight to the box and nothing.

I tried a power inserter dpp44 and nothing. I tried the dpp44 with a line to the lnbs by itself then a second line to the jynx and nothing.

I also tried the jynx with the power inserter "inline" and nothing.

I changed all the settings in the box and nothing.

I also tried a 4x1 switch and could not get signal.

i moved the jb200 to the other slot and nothing.

I also reseted the box and nothing.

I know the box and jb200 works because i tested it with a dual lnb dpplus and i can get signal, just not with my dish!

I am lost, i need help please!!!
With the DPP LNBs in the sat setup menu/Legacy switch off/ Legacy LNB=OCS-DP.

[Glatt]

Use a line checker for a signal!!

[Benney]

Ah bad tuner maybe?

[whoknows]

i have a v2 with loader 1.2.20/firmware 1.2.43/ build date 2013-8-13 and a dpplus with 3 lnbs(they have 3 outputs and 1 input, black writing)

I cannot get signal no matter what i do!

The dish and lnbs works because i have a freesat hd running without any problems or issues.

i tried the lnbs straight to the box and nothing.

I tried a power inserter dpp44 and nothing. I tried the dpp44 with a line to the lnbs by itself then a second line to the jynx and nothing.

I also tried the jynx with the power inserter "inline" and nothing.

I changed all the settings in the box and nothing.

I also tried a 4x1 switch and could not get signal.

i moved the jb200 to the other slot and nothing.

I also reseted the box and nothing.

I know the box and jb200 works because i tested it with a dual lnb dpplus and i can get signal, just not with my dish!

I am lost, i need help please!!!


Use a line checker for a signal!!


He did check with another receiver.

[Fibroso]

With the DPP LNBs in the sat setup menu/Legacy switch off/ Legacy LNB=OCS-DP.

How can you get signal in 119 in that freq. 12224/ 20000

[iq180]

How can you get signal in 119 in that freq. 12224/ 20000
Location/Location/Location/ & know how,LOL.

[Terryl]

12224 is a spot beam on that satellite, in some places you can get a good signal, in others you can't.

That's why I always use TP12475 on 119, it has the open to all ""Dish 101"" channel on it.

[lalord69]

i tried all of those suggestions already. I also ordered an extra jb tuner and it does not want to work. I check all of the recommended TPs using the correct settings and nothing.

Like i mentioned before, what puzzels me is that i took this box to another house and plugged it and i can get signal. I even traded LNBs and i cannot get it to work in my house. I know that i am pointing to the right birds because my freesat hd has 90+% of quality on all 3 birds and runs without any issues.

last thing to do is:

hard reset, then flash back to factory, hard reset, flash bin, hard reset, and try again but at this point i do not have high hopes to get this box to work in my house.

[Terryl]

If it works at another location and you have the same type setup at your location, then it should be working.

The best setup was as you mentioned, the DPP44 power inserter on it's own coax to the #1 output port on the D1000 LNB, then the OCS-DP settings need to be used.

Diseqc switching is as follows.

Diseqc port #1 = 119W, use TP 12457 for signal check.
Diseqc port #2 = 110W, use TP 12224 for signal check.
Diseqc port #3 = 129W, use TP 12516 for signal check.
Diseqc port #4 = open.

And I would try it with the add on tuner removed from the setup as a test.

[iq180]

i tried all of those suggestions already. I also ordered an extra jb tuner and it does not want to work. I check all of the recommended TPs using the correct settings and nothing.

Like i mentioned before, what puzzels me is that i took this box to another house and plugged it and i can get signal. I even traded LNBs and i cannot get it to work in my house. I know that i am pointing to the right birds because my freesat hd has 90+% of quality on all 3 birds and runs without any issues.

last thing to do is:

hard reset, then flash back to factory, hard reset, flash bin, hard reset, and try again but at this point i do not have high hopes to get this box to work in my house.
There is one thing you have overlooked, check the end of your coax cable, if the copper wire is not sticking out 1/16 of an inch past
the end of the coax nut it will not make contact in the JB200 module.