Jynxbox Ultra HD v30 on DishPro Plus AK72-BTE LNBF

[pixim]

hello,

I'm running a Jynxbox Ultra HD v30 on a BEV Dish with a DishPro Plus AK72-BTE LNBF. My signal is up and down between 90% and 40%... With the BEV receiver, the signal stay at 90%...

Can anybody tell me if a know problem occured between the v30 and the AK72-BTE dual lnb? What is the best way to connect the v30 to this lnb and have a good signal all the time?

Thank you!

[Benney]

You do know that has a built in switch?


This is what it really is.

Dish Network Dish Pro Plus Twin LNBF (DPP Twin LNB)

[pixim]

I don't know, but in the pass, I was running two BEV HD receiver, and only one cable plug in to each BEV receiver, so, I guess that LNB have a built in switch sending the two signal over the two cable...

[Benney]

I'm not familiar with the V30 but it is not setup like a Bell Receiver.

You need to setup the ports and LNB types etc for each sat in the V30.

I presume DiSEqC1---port1 is 91 and port 2 is 82.
LNB power on
LNB Freq 11250

[pixim]

OK thank's for the tips!

Can anybody tell me more on configuring the ports and LNB types etc for each sat in the V30 ??

[jets]

and I believe the Legacy LNB would have to be set to OSC-DP, for that LNB :)

[pixim]

Hooow with the OCS-DP setting on the Nimiq 1 I'm good, but I'm not able to have signal on Nimiq4

Here is my setting per Satellite::

Nimiq 1:
tuner: LNB1 (fixed)
LNB Freq: 11250
Transponder )20/29) 12545 V 20000
DiSEqc1.0: Port1
DiSEqc1.1: Off
Legacy SW: Off
Legacy LNB OCS-DP
22K: Off
Polarity: Auto
Signal Intensity: 85%
Signal Quality: 82%

Nimiq 4:
tuner: LNB1 (fixed)
LNB Freq: 11250
Transponder (1/32) 12224 V 21500
DiSEqc1.0: Port1
DiSEqc1.1: Disable
Legacy SW: Off
Legacy LNB OCS-DP
22K: Off
Polarity: Auto
Signal Intensity: 42%
Signal Quality: 42%

Please help me !! :noidea:

[pixim]

Hello,

What is the best setting for nimiq 4 with Dish Network Dish Pro Plus Twin LNBF ?

Actualy I have no signal :noidea:

Nimiq 4:
tuner: LNB1 (fixed)
LNB Freq: 11250
Transponder: (1/32) 12224 V 21500
DiSEqc1.0: Port1
DiSEqc1.1: Disable
Legacy SW: Off
Legacy LNB OCS-DP
22K: Off
Polarity: Auto
Signal Intensity: 42%
Signal Quality: 42%

[iq180]

Hooow with the OCS-DP setting on the Nimiq 1 I'm good, but I'm not able to have signal on Nimiq4

Here is my setting per Satellite::

Nimiq 1:
tuner: LNB1 (fixed)
LNB Freq: 11250
Transponder )20/29) 12545 V 20000
DiSEqc1.0: Port1
DiSEqc1.1: Off
Legacy SW: Off
Legacy LNB OCS-DP
22K: Off
Polarity: Auto
Signal Intensity: 85%
Signal Quality: 82%

Nimiq 4:
tuner: LNB1 (fixed)
LNB Freq: 11250
Transponder (1/32) 12224 V 21500
DiSEqc1.0: Port1
DiSEqc1.1: Disable
Legacy SW: Off
Legacy LNB OCS-DP
22K: Off
Polarity: Auto
Signal Intensity: 42%
Signal Quality: 42%

Please help me !! :noidea:
Set nimiq 4 to Diseqc 1.0 to port 2 for the built in switch to work.

[DJMark]

and I believe the Legacy LNB would have to be set to OSC-DP, for that LNB :)

Yes. I have a very similar setup, just an older Jynx. OSC-DP should be on for best results.

[DJMark]

Try tuner LNB 2, see if that does it. If not then I would probably guess there is an issue with the Dish Pro Plus.

[Anubis]

You need to change tuner to LNB 2 as mentioned in your other post showing your settings. Also you have a clone unit so I have moved your posts to the appropriate section and joined them. Please stick to the one post for this issue.

[Terryl]

The dish DPP Twin LNB (has two eyes on it) is designed for two satellites, ether 110/119 or 91/82.

Trying to use it on a signal satellite is a bit of a challenge.

It has an internal switch so you can't use an external Diseqc switch, it would be Diseqc port # 1 for 119 and port #2 for 110, or Diseqc port # 1 for 91 and port #2 for 82, but you have to align the dish to be right in the middle of the two satellites.

Dishpointer.com will help you find these birds and give you the correct pointing information.

You also have to live within 200 miles South of the US/Canadian border or your not going to be able to get 82 or 91. (If your in Canada then you should have no problems)

[pixim]

Thank you all! My signal is now at 85% !