Nimiq 4 tp22 12530 issue

[jon doe]

I'm not sure this is even an issue with this receiver only but this one transponder will not scan. All others lock fine. Settings are correct. Another person I spoke to has same issue. Any thoughts?

[Terryl]

You don't have a WIFI router close by to the receiver do you?

It is possible for something close to the LO or IF frequency to affect a transponder.

LO = 11250 MHz
IF of this transponder = 1280 MHz

1280 MHz is used for some drones with video downlink.

[jon doe]

Interesting. There is a large wifi access point but not near by. I'll have it disconnected then test again. I'll report back. Thank you

[jon doe]

You don't have a WIFI router close by to the receiver do you?

It is possible for something close to the LO or IF frequency to affect a transponder.

LO = 11250 MHz
IF of this transponder = 1280 MHz

1280 MHz is used for some drones with video downlink.

I had the wifi disconnected but no change. I appreciate the suggestion though. Here are some more facts to think about.
The same problem is happening at two separate locations across 5 different receivers so this is not really a T6 issue, sorry for posting here. Maybe there is a better area to move this post?

Each location has multiple lines, all of which work perfectly except for this one TP. If you test the same line with an actual Bell receiver, Tp22 (12530) on 82w works fine which rules out alignment.
One thing that both locations have in common is they both are connected directly to a TwinDP LNB. One with a DP44 switch and one directly to the LNB. Nonetheless, the result is the same. 12530 will not lock on at all.

Any other thoughts or ideas are very much welcome.
Thank you!

[62bug]

are you able to change the polarity
like if it comes up V try to change to H
Just a thought

[jon doe]

Changing it to H allows it to scan but it scans the wrong TP (not sure which one) and the wrong channels scan in and don't work.

[Goldberg]

Did you ever end up solving this?

Im having the same issue

[johnnylarue]

Did you ever end up solving this?

Im having the same issue

The FEC is 3/4A on that TP. I know on the T5, there is no way to change the FEC to 3/4A. On other receivers, you can.

[Goldberg]

^ I also have a jynbox.

Would it work on that. Cant see where to edit the FEC

[johnnylarue]

^ I also have a jynbox.

Would it work on that. Cant see where to edit the FEC

I am not familiar with jynxbox, but that fix works with Sonicview 8000. Maybe some jynxbox expert will know.

[jon doe]

The FEC is 3/4A on that TP. I know on the T5, there is no way to change the FEC to 3/4A. On other receivers, you can.

Have you successfully done this and been able to scan this tp using any receiver at all?

[johnnylarue]

Have you successfully done this and been able to scan this tp using any receiver at all?

yes, with my sv8000 and my genpix/dvb.

[jon doe]

Hmmm I've tested with an sv8000 with no success. I'm going to recheck the Fec and try again.
Thank you

[johnnylarue]

Hmmm I've tested with an sv8000 with no success. I'm going to recheck the Fec and try again.
Thank you

Add 12530 as a new TP. Don't edit the one from the bin. it is FEC 3/4A, 21500, turbo-8psk, H or Auto works. It works perfect. Watching MLBHD right now.

[Goldberg]

^ Thanks.

Do you know of any TPs that need editing to work on Bev?
Wouldnt mind extra channels

[jon doe]

Confirmed working with Sonicview 8000HD by doing what johnnylarue said. Set the FEC to 3/4A and it scans in the proper channels no problem.

Sorry, its not that I didn't believe you, its just that I had spent quite some time trying to make this work with no success. I'm very glad to have the answer now.
Thank you!

[baseman]

Has anyone got this fixed for the t5? I still don't get a scan...red bar since wifi turned on last year :(

[jon doe]

No FEC options on t5 so I don't see how it's possible.

[YoHo]

No FEC options on t5 so I don't see how it's possible.

Yes, you can change the FEC on the T5. Menu + Installation + Manual Scan + FEC

[jon doe]

If you set it for 3/4 then it might work. On the sv8000 it needs to be 3/4a. On the viewsat 9000 3/4 does not work but on the genpix 3/4 does work. Try it and let us know.

[baseman]

Yes, you can change the FEC on the T5. Menu + Installation + Manual Scan + FEC

I tried the FEC + 3/4 but no change at all...I tried others :(

[johnnylarue]

I tried the FEC + 3/4 but no change at all...I tried others :(

It won't work. The T5 has no setting for 3/4A.

[jets]

T5 work just set Turbo and 3/4, 3/4A not necessary.

[jon doe]

T5 work just set Turbo and 3/4, 3/4A not necessary.

Not working for me. Anyone else with a T5 have success trying this?

[wsc]

having same problem with jynxbox v2. Can't get channels on tp22.

[danny]

Has anybody been able to scan the TP 22 (12530) on the Dreamlink T5 for the MLB Network HD?

[nobodyspecial]

Has anybody been able to scan the TP 22 (12530) on the Dreamlink T5 for the MLB Network HD?
no there are threads going back over a year about this channel
wont work on a t5

[guy]

Thanks guys works on sv 8000

[jon doe]

Thanks guys works on sv 8000

It does scan on an SV8000 but many reports of video frame timing issues with 8psk turbo on 82 on the SV8000 which seem to lead to video stutter. Not sure if it happens to everyone though. Good luck.

[foresight]

Considering the support dried up on most of these older stb's 5 to 10 yrs ago any glitches or issues that were there are most likely still there. Unless someone came up with a work around. Think LB was still supported up to a year or so ago but looks as if it has dried up as well now. Been a lot of moving around of the furniture with a lot of the birds since a lot of these files were wrote to boot that may not help matters.

[danny]

Thanks guys works on sv 8000

How do you get it to scan on SV 8000. Tried 12530, 21500, H, 3/4A, Turbo 8. Nothing scans (scan failed). The quality is 100% and strength is 58% for this TP.

Also all the channels are coming in at MPEG 4 720i. Should it not display 720P on SV 8000?

[guy]

quality looks low to low turn network search off very very impotant then push scan tp mpeg 4 720 is right
How do you get it to scan on SV 8000. Tried 12530, 21500, H, 3/4A, Turbo 8. Nothing scans (scan failed). The quality is 100% and strength is 58% for this TP.

Also all the channels are coming in at MPEG 4 720i. Should it not display 720P on SV 8000?

[foresight]

How do you get it to scan on SV 8000. Tried 12530, 21500, H, 3/4A, Turbo 8. Nothing scans (scan failed). The quality is 100% and strength is 58% for this TP.

Also all the channels are coming in at MPEG 4 720i. Should it not display 720P on SV 8000?

From my read anything above 50% quality wise should work. Although that would be bare minimum and would not be recommended as it would cause issues. If one is getting 100% quality then it doesn't get much better. Problem with these stb's is there meters are not always accurate. As to the SV8K showing 720i seems to be a common issue. Jmo but my guess would be an issue in the way the sw was wrote years ago. Guess it could explain the slight shutter issue as well. I do know it will show 720p with the atsc tuner. This issue has came up in other posts so I did a little googling a while back. And from what I read at one time there was some thought of having a 720i resolution prior to around 2008 if memory serves. But in the end they decided on just 720p. If that was the case then it is possible considering the date when the SV8K was manufactured and sw wrote they may wanted to cover all the basis and it was wrote in just in case. The date fits anyway as it all falls around 2007 and 2008 from jump. One can google i vs p with the resolution and find out the difference.

If you see the sat. info appear in the light blue area in the upper right hand corner while in dish settings you should be good. More quality the better as the strength side of the meter can be fickle. Seen it anywhere from 54 to zero with strength and scan depending on bird if the quality was strong. Strange tp as it does weird things at times

[guy]

I have 4 8000s and none would work with your low quality the signal means nothing check your other tps for quality and you will see

[danny]

I have 4 8000s and none would work with your low quality the signal means nothing check your other tps for quality and you will see

The quality and signal are same on all other TP's, and they all scan fine, except this TP does not scan. The sat. info appear in the light blue area in the upper right hand corner on this TP. So I don't think the quality is the issue.

Let me know if I am inputting the TP info correctly. I have it as 12530, 21500, H, 3/4A, Turbo 8. Should the FEC be 3/4A, as I have it or should it be something else?

[foresight]

S-54 Q-53 here and works but not even close to ideal. With the info you have and a reading of S-58 Q-100 it should work. Of coarse I maybe missing something as it's early and my eyes are feeling weak at the moment along with my brain. A little better reading with a different stb. Also seen quality levels go up and down slightly depending on the time of day. Figure it is due to being on the fringe and or atmospheric conditions. That issue doesn't seem to be specific to just one tp. As been said the higher the S&Q the better. Best to tweak the dish off the weakest tp.

[Terryl]

The info for 82W TP 12530 showing on Lyngsat (and some others) may be old, but it shows the FEC to be 2/3 not 3/4, maybe this is a problem.

More info:
https://www.usatellites.com/2018/07/nimiq-4-820w-ku-band-satellite.html

[foresight]

Most updated info on that bird below that I'm aware of:





82W
1.12224 21500 (V) 2/3 Turbo 8PSK
2.12239 21500 (H) 2/3 Turbo 8PSK
3.12253 21500 (V) 2/3 Turbo 8PSK
4.12268 21500 (H) 2/3 Turbo 8PSK
5.12282 21500 (V) 2/3 Turbo 8PSK
6.12297 21500 (H) 2/3 Turbo 8PSK
7.12311 21500 (V) 2/3 Turbo 8PSK
8.12326 21500 (H) 2/3 Turbo 8PSK
9.12341 21500 (V) 2/3 Turbo 8PSK
10.12355 21500 (H) 2/3 Turbo 8PSK
11.12370 21500 (V) 2/3 Turbo 8PSK
12.12384 21500 (H) 2/3 Turbo 8PSK
13.12399 21500 (V) 2/3 Turbo 8PSK
14.12413 21500 (H) 2/3 Turbo 8PSK'
15.12428 20000 (V) 7/8 QPSK'
16.12443 20000 (H) 7/8 QPSK
17.12457 21500 (V) 2/3 Turbo 8PSK
18.12472 21500 (H) 2/3 Turbo 8PSK
19.12486 21500 (V) 2/3 Turbo 8PSK
20.12501 21500 (H) 2/3 Turbo 8PSK
21.12516 21500 (V) 2/3 Turbo 8PSK
22.12530 21500 (H) 3/4A Turbo 8PSK
23.12545 21500 (V) 2/3 Turbo 8PSK
24.12559 21500 (H) 2/3 Turbo 8PSK
25.12574 21500 (V) 2/3 Turbo 8PSK
26.12588 21500 (H) 2/3 Turbo 8PSK
27.12603 21500 (V) 2/3 Turbo 8PSK
28.12618 21500 (H) 2/3 Turbo 8PSK
29.12632 21500 (V) 2/3 Turbo 8PSK
30.12647 21500 (H) 2/3 Turbo 8PSK
31.12661 21500 (V) 2/3 Turbo 8PSK
32.12676 21500 (H) 2/3 Turbo 8PSK
--------------------------------------------

[The Noof]

It does scan on an SV8000 but many reports of video frame timing issues with 8psk turbo on 82 on the SV8000 which seem to lead to video stutter. Not sure if it happens to everyone though. Good luck.

Happens to all the SV 8000hd's I know of.Best results are to use component cables rather than hdmi,& set resolution to 720p.Not a cure, but it's much better.

[danny]

The info for 82W TP 12530 showing on Lyngsat (and some others) may be old, but it shows the FEC to be 2/3 not 3/4, maybe this is a problem.

More info:
https://www.usatellites.com/2018/07/nimiq-4-820w-ku-band-satellite.html

Can somebody check their setting on the Sonvicview 8000, and let me know what settings they have for this TP?

[guy]

you have the right settings
the signal strength isnt that important you need better quality its what counts not sig strngth
I have lots of tps shoe high 90s quality and no signal--0
maybe you are to far south ?????????
​Quality

[danny]

you have the right settings
the signal strength isnt that important you need better quality its what counts not sig strngth
I have lots of tps shoe high 90s quality and no signal--0
maybe you are to far south ?????????
​Quality

My quality is 100% and strength is 58%.