Channel issues with Dreamlink T5 HD 82 91

[szymi2015]

When I change channels they are on and off. It takes about 10-15 sec to load each channel. If a channel is not working it say "bad or no signal". When i go to cp24 and then cnn it works but when i go back to cp24 it doesn't works again. If I go to another channel like tlc and than back to cp24 it works.
As well not all channels work I have scanned a few times and I did a factor reset.

[nobodyspecial]

When I change channels they are on and off. It takes about 10-15 sec to load each channel. If a channel is not working it say "bad or no signal". When i go to cp24 and then cnn it works but when i go back to cp24 it doesn't works again. If I go to another channel like tlc and than back to cp24 it works.
As well not all channels work I have scanned a few times and I did a factor reset.

post your lnb type ,switches if any and your settings for your sats

[szymi2015]

Hopefully this is what you need.

Digital LNBF, AK72-BTE, Lot No. W205

26752267502674826751
26749

[nobodyspecial]

I need more info Do you have other receivers in this set-up?

Secondly why do you have 82 set up in motor settings?
thirdly you have no switch settings These need to be set up

[szymi2015]

The box that we have was preloaded when we got it.
We don't have any other receivers.
As far as I know the motor is not active
I don't know what switch settings are.
All of these issues started when my 2 year old did something to the settings.

[jvvh5897]

Well, there you go!--operator error. Switch settings are in part of the dish installation menu. I would expect that the LNB LO was changed--it should be 11.250 GHz I think. If the channel eventually comes in, it implies that the correct LNB is being selected, but if the LNB LO is set incorrectly the tuner may be able to do a search through a wide enough range to find the TP. Course it could be any of the dish settings.

[nobodyspecial]

Well, there you go!--operator error. Switch settings are in part of the dish installation menu. I would expect that the LNB LO was changed--it should be 11.250 GHz I think. If the channel eventually comes in, it implies that the correct LNB is being selected, but if the LNB LO is set incorrectly the tuner may be able to do a search through a wide enough range to find the TP. Course it could be any of the dish settings.

setting are all wrong too the lnb is a dishpro twin plushttp://i.ebayimg.com/00/s/MTEwOFgxMDk1/z/s1kAAOSwmgJY3VIi/$_57.JPG?set_id=880000500F

[szymi2015]

We have it set to 11.250 GHz. We have had a lor of rain in the last few weeks could this cause the issue?

What is TP and LNB LO?

[szymi2015]

What should thr settings be on the LNB?

[nobodyspecial]

What should thr settings be on the LNB?

what about other receivers in set-up?

[chevy222]

This dpplus already have a switch intergraded no need your small splitter switch you have 3 ouput on your lnb connect only one output by recever the lnb switch 91 to 82....for my part i have same lnb and only one ouput to my t5 and im run both satellite 82 and 91 Whit no external switch. .splitter etc...

[szymi2015]

This is the only receiver I have

[szymi2015]

How do I get the right settings?

[nobodyspecial]

I dont have access to a t5 so I am going by memory
You need to lose that dp separator and run cable straight to rcvr Make sure the power switch is off in back of t5 when doing this.
Lnb type will be dishpro If there is a dishpro twin in settings use it If not just use dishpro
Turn diseq on and assign 91 to port 1 ,82 to port 2

[szymi2015]

I dont have access to a t5 so I am going by memory
You need to lose that dp separator and run cable straight to rcvr Make sure the power switch is off in back of t5 when doing this.
Lnb type will be dishpro If there is a dishpro twin in settings use it If not just use dishpro
Turn diseq on and assign 91 to port 1 ,82 to port 2

It worked. They actually load normally. You are awesome for knowing this stuff and helping me out. Have a great weekend:-)

[bcbud]

try changing to single LNB 's, not sure , but think, they don't work on your receiver had the same problem, those LNB's need to use a separator to your receiver and that needs 2 in's to connect 2 and your receiver has 1 in and 1 out hope this helps

[nobodyspecial]

try changing to single LNB 's, not sure , but think, they don't work on your receiver had the same problem, those LNB's need to use a separator to your receiver and that needs 2 in's to connect 2 and your receiver has 1 in and 1 out hope this helps

I think you are smoking too much of your product...lol