Best receiver for North?

[pixim]

Hi I'm actually running a Jynxbox ultra HD v30, I always have duplicate channel, and the HD channel are not working (no signal)... My dish is connected to a LNBF AK72-BTE. What is the best receiver can I buy to have HD channel working?

Thank you!!

[6666]

Hi have same box runs amazing on HD try changing your sat dish maybe will help

[pixim]

What are you using (Dish/LNB) ?

[nobodyspecial]

either your board has gone or your setup is wrong or as stated lnb is offline
you running cable straight to receiver,no switch?
what are your settings for 91 and 82?
If your board is gone you will not be able to get the hd that are on sat 91
155 156,888,and 1041 are hd Can you get them?

[jets]

the jynxbox does not work well with SW21 or SW44 I have heard. Try running legacy LNB's with either a diseqc or a 22KHz switch

[nobodyspecial]

the jynxbox does not work well with SW21 or SW44 I have heard. Try running legacy LNB's with either a diseqc or a 22KHz switch
those dont work well with a dishpro twin either jets...lol

[jets]

yes those too.

[nobodyspecial]

yes those too.

thats what he is using We need to hear back with some more info

[pixim]

Cable direct in the receiver, no switch, wired to the router, no wifi...

If I reset the unit, and do a scan on the 82, I will be able to see the channel, but when I scan the 91, I lost acces to the HD channel (No signal found)... Very sad :(

[nobodyspecial]

Cable direct in the receiver, no switch, wired to the router, no wifi...

If I reset the unit, and do a scan on the 82, I will be able to see the channel, but when I scan the 91, I lost acces to the HD channel (No signal found)... Very sad :(

does the correct sat show up in settings before you scan?

[knob]

hm, 82 is all on the hd board.....are the transponders you're trying to get set for 21500 and 8psk or are they 20000? check the settings ..if you're getting hd channels on 82 the 8psk board is ok, are you getting standard channels on 91?...you say no switch and one cable but it's two sats, you must have a switch or a dual lnb with built in switcher.
i have a sonicview and i had to manually change some tp's to 21500 to get a signal ....they've been slowly changing the tp's on 91, some are still 20000 but only 21500 for hd as all of 82 was changed a few years ago.

[nobodyspecial]

hm, 82 is all on the hd board.....are the transponders you're trying to get set for 21500 and 8psk or are they 20000? check the settings ..if you're getting hd channels on 82 the 8psk board is ok, are you getting standard channels on 91?...you say no switch and one cable but it's two sats, you must have a switch or a dual lnb with built in switcher.

he has a dishpro twin

[knob]

he has a dishpro twin

is he getting channels on both sats? if so it could be he needs to change some tp frequencies

[dishuser]

still need to assign a switch setting for both sats

[knob]

still need to assign a switch setting for both sats

pixim isn't helping us help him,lol....if he reads all these answers something here should fix it.

[pixim]

OK guys sorry for the delay. I'm doing some test this morning... I have deleted all the channel, and scanned the 82 sat... Got a list of channel... It's ok for a time, but when I change the channel, I have "So Signal found"... I need to go on the Sat setting, move to the next transponder, then the signal is back, and return to the channel. This case appear only on the 82 sat. On the 91, my signal is always good...

Here are the setting on the 82:
Sat: 82
Tuner: LNB1 (Fixed)
LNB Freq 11250
Transponder 1/32 (I have no signal I need to go on transponder 9 to have signal)
DiSWqC1.0 Disable
DiSWqC1.1 Disable
Legacy SW off
Legacy LNB off
22k off
Polarity auto

[harry3456]

Try assigning a port to diseq 1.0

91 Should be port 1
82 Should be port 2


Also, if you're using Dish Pro LNB's you'll need to change to that if it's an option in the frequency.
Can't remember what Jynx has. Frequency (11250 Dish Pro)

[pixim]

the jynxbox does not work well with SW21 or SW44 I have heard. Try running legacy LNB's with either a diseqc or a 22KHz switch

Wich option did I take on the Legacy LNB( Twin, Quad, OCS-DP)?

[pixim]

New auto scan (what is blind scan) with some recommendation:
Sat: 82
Tuner: LNB1 (Fixed)
LNB Freq 11250
Transponder 5/32 12282 V 21500
DiSWqC1.0 Port 1
DiSWqC1.1 Disable
Legacy SW off
Legacy LNB OCS-DP
22k ON
Polarity auto

Scan complete with only channel 48 :(

[harry3456]

Sounds like may be your dish moved? Maybe you don't have signal and quality on all TP's. There is a chance that your settings are off. I can't find where you confirmed your dish and LNB type. Maybe I missed it. Post some pics if you can of the dish and LNB.

[marcel.crash]

i would try these setting :

Sat: 91
Tuner: LNB1 (Fixed)
LNB Freq 11250
Transponder 1/29 12224 v 20000
DiSWqC1.0 Port 1
DiSWqC1.1 Disable
Legacy SW off
Legacy LNB OCS-DP
22k Off
Polarity auto


Sat: 82
Tuner: LNB1 (Fixed)
LNB Freq 11250
Transponder 1/32 122224 v 21500
DiSWqC1.0 Port 2
DiSWqC1.1 Disable
Legacy SW off
Legacy LNB OCS-DP
22k off
Polarity auto