New t5 today.

[wilfredw]

Got my factory file in and my server in but won,t scan in bev channels.Got it set on turbo but get nothing.Any ideas.

[fn59]

Post the settings you're using, and the dish/lnb type you're hooked up to.

[nobodyspecial]

Post the settings you're using, and the dish/lnb type you're hooked up to.

post the system info too
you did load software file?

[beefcake]

Turbo doesn't have BEV to scan in .

[wilfredw]

Would you be able to connect to server without software?System Info dream.t5 8psk loader l1.00.00 ht v20 1.00.00 ver 1.06.00

[wilfredw]

Lnb power on lnb single is what I have freq 5.150 signal and quality in high 90s.

[nobodyspecial]

Would you be able to connect to server without software?System Info dream.t5 8psk loader l1.00.00 ht v20 1.00.00 ver 1.06.00

you have latest file loaded
post your hardware and settings

[wilfredw]

Not sure exactly what your looking for I posted some info earlyer.I was using setup for my jynxbox until it calfed last month.

[nobodyspecial]

your lnb type ,switches if any, and your settings for 82 and 91
your signal and quality should be in blue

[surfinisfun]

Got my factory file in and my server in but won,t scan in bev channels.Got it set on turbo but get nothing.Any ideas.

Tranmision for bev should be DVBS QPSK

[nobodyspecial]

bell has been turbo 8psk since 2011

[surfinisfun]

Tranmision for bev should be DVBS QPSK


bell has been turbo 8psk since 2011

i think its best to scan under DVBS QPSK

Just a hunch, take it for what its worth. Can't hurt to try.

[nobodyspecial]

i think its best to scan under DVBS QPSK

Just a hunch, take it for what its worth. Can't hurt to try.

good for the sd but why use a 8psk board?
just a hunch you might need it for hd...lol

[wilfredw]

your lnb type ,switches if any, and your settings for 82 and 91
your signal and quality should be in blue

Nlb freq 12.2-12.7 lo11.25ghz if 950-1450 Box has no nimiq sats sinals are in red

[scooby8888]

that freq is off it should be 11250 on the lnb with no switch everything should be off we need to know what lnb and switch you are using

[nobodyspecial]

Nlb freq 12.2-12.7 lo11.25ghz if 950-1450 Box has no nimiq sats sinals are in red

you need to do a factory set after loading the software file

[nobodyspecial]

that freq is off it should be 11250 on the lnb

the low on his lnb is 11250

[surfinisfun]

good for the sd but why use a 8psk board?
just a hunch you might need it for hd...lol

Guess that's true, it would only be good for 91

[wilfredw]

that freq is off it should be 11250 on the lnb

OK Changed that.

[wilfredw]

I have my dish solid on 82.

[scooby8888]

do you have 2 lnbs and a switch or a dishpro lnb from bell or ?

[surfinisfun]

Maybe scan 91 DVBS QPSK and 82 TURBO

[wilfredw]

do you have 2 lnbs and a switch or a dishpro lnb from bell or ?

No just one.

[wilfredw]

OK Changed that.

Since I changed to 11.250, I have no signal.

[nobodyspecial]

you stated you have no nimiq sats in your sat list and you wont until you perform a factory set
AFTER that you set up your sats and scan

https://www.satfix.to/showthread.php?176041-Dreamlink-T5-HD-Set-Up-Info

[wilfredw]

you need to do a factory set after loading the software file

I did that, should I do over?

[wilfredw]

you stated you have no nimiq sats in your sat list and you wont until you perform a factory set
AFTER that you set up your sats and scan

https://www.satfix.to/showthread.php?176041-Dreamlink-T5-HD-Set-Up-Info

Did another fac reset and there are ni iqs thanx channels are scanning

[scooby8888]

then i'm assuming you have a dishpro quad look up a pic and if it is you have to set the lnb type to ocs dp then lnb freq to 11.250 on the 91 you have to set the diseqc sw1.0 to 1 then when you do the setting for the 82 its the same ocs dp then lnb to 11.250 but the diseqc 1.0 has to be changed to 2
..

.

[wilfredw]

Thanx nobody surfin scooby I,m watching tv.One thing though volume buttons don,t want to work.

[scooby8888]

try the buttons around the ok button if its the same remote i have

[wilfredw]

try the buttons around the ok button if its the same remote i have

Thats the fix.

[dishuser]

Turbo doesn't have BEV to scan in .

that was helpful...lol

[surfinisfun]

Thats the fix.

One final tip from me to you...

When you press the return button twice it will show the last nine channels.

Enjoy

[wilfredw]

Sorry to bother you guys again but sports pacs didn, scan in, I need nhl pac.

[nobodyspecial]

Sorry to bother you guys again but sports pacs didn, scan in, I need nhl pac.
the games must be on to scan in
keep scanning evenings until you have them all

[dishuser]

Sorry to bother you guys again but sports pacs didn, scan in, I need nhl pac.
when did you scan?
you need to scan when games are on