UD Error

[intelpenny4]

hello everyone i am having the UD Error with my sonicview 8000. i have tried to reload the H20-2028 no luck.does not throw error when wiznet board is not install

[auggie]

I found this Not my work: SV8000HD Fix for UD Error only!

Here is a UD ERROR FIXED for anyone who's experiencing UD ERROR message.

Please read this instruction carefully before process .

1. Copy HD8000_V0211.rom and HD8000_BOOT_v0200.ldr onto the USB memory stick (make sure to format the USB memory stick prior doing update)

2. Turn SV-HD8000 OFF completely, including the rear power switch

3. Plug the USB memory stick into SV-HD8000 USB port

4. Update "HD8000_V0211.rom" by hard update (Press and Hold front panel
Menu button, at the same time turn the rear power switch ON, when you see it start loading you can release the menu button)

5. Ignore "UD ERROR" message during update. (It can be wrong message)

6. Check if the receiver is booting correctly, if not after 5min, turn OFF and ON by using the rear power switch

7. Go in to Menu and check if the current Main SW version is 02.10

8. Now go to USB Menu, update bootloader with "HD8000_BOOT_v0200.ldr" and you are done .

DO NOT USE THIS FIXED IF YOU ARE NOT EXPERIENCING UD ERROR MESSAGE.

https://www.satfix.to/showthread.php?220033-UD-Error-fix-File&p=1339436#post1339436

[intelpenny4]

i have tried that already with no luck. when i check the main SW version it says 2.11-P

[The Noof]

Try a different usb drive too.SV can be fussy about drive size.Smaller FAT32 is best.

[intelpenny4]

i also tried that too and no luck. think maybe my wiznet board is bad? the firmware is 4.12

[auggie]

i also tried that too and no luck. think maybe my wiznet board is bad? the firmware is 4.12


Version 4.12 is correct, are you using a IHUB or Wiz-board ?

[intelpenny4]

i am using the wiz board

[auggie]

If you run the Wiznet program, does it see it or recognize the board etc. and show that ver. 4.12 is on it ?

[intelpenny4]

yes the program can see it and it also does say its version 4.12

[auggie]

Well if Wiznet can see it & with 4.12 loaded on, it should be good, is the SV8000 NON Responsive other than that
Could you possibly force Load a FACTORY File, or system clean file etc. I don't know what to tell you, but maybe
just keep trying different things to make it GO OR Respond some how. At this point I don't think you can hurt it any worse ?
Hopefully someone with Better Understanding than I have on the SV8000 WORKINGS will Chime in with an answer.

[intelpenny4]

i thank you much and will keep trying my best. like you said cant hurt it anymore then what it is now

[auggie]

I found this Read Me: Main reasons for UD Error update failures:

1. USB Drive not compatible (may look like it works... but it does not). Buy a different type or even a few different types. I've been using a Kingston USB stick and things have been fine (just make sure it is just a USB drive and not anything fancy with extra bells and whistles) When you are in Windows Explorer, right click your memory stick and select Format. Always be sure your drive is reformatted to FAT. Some reformat there USB drive before every file load.

2. Memory sticks sometimes have multiple boot partitions/devices which foul up the process and the Sonicview 8000 will see the wrong device. Things like thumb security, backup software, automatic driver install partitions, etc are examples of multiple devices on one memory stick. Try and find a simple USB stick thats only a storage device and nothing else.

3. USB port acts erratic when there is a large power drain on the unit. I've goofed around with addons and stuff and sometimes the power drain causes the USB to act screwy. Take out anything that draws power on your Sonicview receiver, and just have the TV plugged in.

4. You have a zip file on the drive stick and not the uncompressed bin/rom file. Unzip the file then copy it over to the drive stick. Never uncompress directly to USB drive. This has been known to cause some data corruption.

5. You copied the file over and didn't add/remove the USB drive stick from your PC using the "safely remove" icon from the tasktray (lower right) or in My Computer. The File can get corrupted on the memory stick and looks good (the file is there) but its missing some bits of data and dies in the update process (midway or near the end). Re-Download and Copy a fresh version of the file, unzip, then copy the fresh file to the drive stick and then safely remove the USB drive from the PC.

6. File downloaded from the site got corrupted in the transfer somehow. Its unlikely, but it has happened. Re-Download and try again.

7. Older versions of firmware didn't support larger USB memsticks. Try to use 1GB and lower. 512MB seems to be the most stable if you are going back and forth between firmware revisions.

If you're trapped with a non working USB memory stick but your PVR drive works, you can use that instead. Hook the drive up to your PC, copy the bin/rom file to it (the root folder of the drive) and reconnect it to the Sonicview 8000, then go to the USB menu and manually do the software update from there.

[intelpenny4]

i want to thank you again. i have tried over seven usb drives and no change. i tried loading older firmwares also n no luck there either. i am going to see if i have another wiznet or even a ihub and see if that changes anything

[auggie]

intelpenny4 (https://www.satfix.to/member.php?u=106948) Check your P.M. I left you a message about IHUB

[chad1976]

soniceview coder suck!!!!!!!!!!TIME BOME

[intelpenny4]

well i want to say thank you to auggie for helping me and telling me what to do and try. i want to report that doing the factory flash and system clean up over six times did the trick.

[auggie]

well i want to say thank you to auggie for helping me and telling me what to do and try. i want to report that doing the factory flash and system clean up over six times did the trick.


Perseverance Does Pay Sometimes, Glad you Fixed it, :yeaah::thumbsup:

[intelpenny4]

well the UD error came back after two weeks and i didnt Pay any attention to it and set it aside and went back to my T5. but last week i wanted to use my SV8000 again to only remember that UD error was still there so i buckled down and wasn’t going to give up this time to fix it for good. i had help the whole time from Auggie and stayed by my side through it all with me. the problem was the 2028 file wasn’t working for me and kept getting the UD error and then finally Auggie uploaded a newer 2028 file and bam it all worked out and is working stronger then ever and i am very greatful for having Auggie by my side and lots of thank you goes out to him thank you thank you.


again to everyone that’s on this site helping and paying it forward thank you so much for everything

[ssj92]

Is the file @auggie posted considered the "latest" file for hd 8000? And it doesn't need SVLan or iHUB adapter? I want to update my receivers

[auggie]

Is the file @auggie posted considered the "latest" file for hd 8000? And it doesn't need SVLan or iHUB adapter? I want to update my receivers


There is NO LATEST FILE for the HD8000, File support stopped long ago and all need a wiz-board or Dongle to make them "GO"

[intelpenny4]

i use the wiz board i feel they work better and last longer. i used the new 2028 file auggie uploaded and that worked for my UD error

[ssj92]

Sorry , meant which file is considered latest as in has the newest firmware etc. Sounds like the 2028 file is what was last made?

BTW I don't remember anything about a wiz board. I do have either a svlan or ihub sitting around from years ago.

Can someone shed some details on what it is? lol

[auggie]

It is one of these:hxxps://www.digikey.ca/en/products/detail/wiznet/WIZ110SR/3829651

Ethernet Adapter etc. similar to the IHub, which are still available I believe (wiz-board)