galaxy 97.0w or Telstar 970w

[leskfee]

Hi, everyone
I am trying to get the right antana setting for capitivework 600 p>?
I couldn't find Galaxy 19 9w in this receiver, i did find Telstar 97.0w is that correct sat to point and getting signal.
thaks for help!

[secheltpaul]

yes that is the same one just an older listing in your stub.I also have a cw600 .
good luck.

[secheltpaul]

Here are a few transponders that are strong for me in the Vancouver area this morning on G19 97west

Freq pol s/r fec
12090 H 20000 ¾
12177 V 23000 2/3
11836 V 20765 2/3
11867 V 22000 3/4

[leskfee]

Here are a few transponders that are strong for me in the Vancouver area this morning on G19 97west

Freq pol s/r fec
12090 H 20000 ¾
12177 V 23000 2/3
11836 V 20765 2/3
11867 V 22000 3/4

thank you my friend for good info............

[leskfee]

Here are a few transponders that are strong for me in the Vancouver area this morning on G19 97west

Freq pol s/r fec
12090 H 20000 ¾
12177 V 23000 2/3
11836 V 20765 2/3
11867 V 22000 3/4

hi, my friend what antena seting do have for 22HZ do have OFF or Auto.
thanks

[Terryl]

Use the 22 KHz setting only if you have a 22 KHz switch in your system, if you run directly to the LNB from the receiver then set it to “OFF”, if you have 2 dishes connected to a 2 input 1 output 22 KHz switch then you need to know what input this dish is using, one dish will go to the “OFF” side of the switch, the other dish to the “ON” side, you set the 22 KHz option to “ON” or “OFF’ depending on how you hooked it up.

[leskfee]

Use the 22 KHz setting only if you have a 22 KHz switch in your system, if you run directly to the LNB from the receiver then set it to “OFF”, if you have 2 dishes connected to a 2 input 1 output 22 KHz switch then you need to know what input this dish is using, one dish will go to the “OFF” side of the switch, the other dish to the “ON” side, you set the 22 KHz option to “ON” or “OFF’ depending on how you hooked it up.

thanks a lotTerry got it

[secheltpaul]

Leskfee, Follow Terryl’s instructions there perfect .

[leskfee]

Leskfee, Follow Terryl’s instructions there perfect .

thanks my friend, i know he is a very helpful and always gives useful ifro...
thanks my friend Terry for your time to help ..... thakn a lotttttt

[chifut]

.... some LNBs/universal/ need turn ON 22kHz in the setting

[TurboPirate]

Hi, everyone
I am trying to get the right antana setting for capitivework 600 p>?
I couldn't find Galaxy 19 9w in this receiver, i did find Telstar 97.0w is that correct sat to point and getting signal.
thaks for help!

You got your answers, but I'll add something, always check or look for the sat in your receiver by position, west, never look them by name, many sats have change names and that info is not updated on each receiver, if the sat you are looking is Azteca 93.1west, well just look for 93west and that is the sat you are looking for. this as an example.

[WillDekkard]

.... some LNBs/universal/ need turn ON 22kHz in the setting

You only set it to ON if you do not have an AUTO setting for your Universal LNB. Most FTA receivers will automatically default to AUTO when selecting Universal.