Nanosat Premium SE - Legacy LNB Set up 119, 110,61.5

[anarchista]

Hello. Using Legacy Lnb's somewhat complicates the set up since these are more and more scarcely used. I have not been able to find set up info on combination that I am attempting to make work. So if anyone can help it will be appreciated.

Subject: what switch(es) should be used and what will be correct settings in receiver.
Object: to combine Echo* 14,119 and 10/11, 110 on Dish 500 WITH 12/15, 61.5 on separate dish, Dish 300.
Hardware: 1st dish - Dish 500 equipped with Legacy Twin Lnb (2Lnb's in oval housing) + 2nd dish - Dish 300 equipped with Legacy Dual Lnb (1Lnb).
Receiver: Nanosat Premium SE
Notes: A.) Dish 300 for 61.5 is not used in bellow working setup however it is aimed at the bird and signal locked. Also DO HAVE switch sw21 but any other will have to be additionally obtained.
B.) set up & settings for 1 receiver only. But if you know how to do 2 receivers with this gear please post it as well.

Current working setup / settings:
Dish 500, 119 and 110 do work flawlessly.
Sat: 14, 119
DiSEqC: None
DiSEqC 1.1: None
TP Frequency: 12253 (Locked)
LNB: 11250
22 KHz Tone: OFF
Multi-Dish Switch: SW 42 Dish 1
Search Options: ALL Channels
LNB Power: ON

Sat: 10/11, 110
DiSEqC: None
DiSEqC 1.1: None
TP Frequency: 12224 (Locked)
LNB: 11250
22 KHz Tone: OFF
Multi-Dish Switch: SW 42 Dish 2
Search Options: ALL Channels
LNB Power: ON

Now - to the above set up (that works very well) how would one add the 12/15, 61.5.
1.) What Switch(es) shall be used, will SW21 work by itself or should it be combined with any other additional hardware?
2.) How it should be connected (connection diagram)?
3.) What will be the correct settings in receiver?
I have found answers to the above questions on similar setups but not exactly on this one (mostly on DishPro etc. which is a bit different) or receiver different.

A.)If you recommend equipment & connection (as per above questions), please if you can fill info in receiver settings (bellow):
Sat: 12/15, 61.5
DiSEqC: ????
DiSEqC 1.1: ????
TP Frequency:????
LNB: 11250
22 KHz Tone: OFF
Multi-Dish Switch: ????
Search Options: ALL Channels
LNB Power: ON

B.) Will there be changes to settings on / to the 119 and 110 ? In all probability yes. Can you advice as well.

Thanks to all of you in advance.

[anarchista]

Hmmm... nobody has an answer? That is precisely why I posted this. Compare to lot of other problems in testing this should be a trivial issue ... yet no answer. Well I'll give it few more hours ... then will have to take it to different forum. Beginning to suspect there in not enough traffic on this forum.

[pugsycan]

Hello. Using Legacy Lnb's somewhat complicates the set up since these are more and more scarcely used. I have not been able to find set up info on combination that I am attempting to make work. So if anyone can help it will be appreciated.

Subject: what switch(es) should be used and what will be correct settings in receiver.
Object: to combine Echo* 14,119 and 10/11, 110 on Dish 500 WITH 12/15, 61.5 on separate dish, Dish 300.
Hardware: 1st dish - Dish 500 equipped with Legacy Twin Lnb (2Lnb's in oval housing) + 2nd dish - Dish 300 equipped with Legacy Dual Lnb (1Lnb).
Receiver: Nanosat Premium SE
Notes: A.) Dish 300 for 61.5 is not used in bellow working setup however it is aimed at the bird and signal locked. Also DO HAVE switch sw21 but any other will have to be additionally obtained.
B.) set up & settings for 1 receiver only. But if you know how to do 2 receivers with this gear please post it as well.

Current working setup / settings:
Dish 500, 119 and 110 do work flawlessly.
Sat: 14, 119
DiSEqC: None
DiSEqC 1.1: None
TP Frequency: 12253 (Locked)
LNB: 11250
22 KHz Tone: OFF
Multi-Dish Switch: SW 42 Dish 1
Search Options: ALL Channels
LNB Power: ON

Sat: 10/11, 110
DiSEqC: None
DiSEqC 1.1: None
TP Frequency: 12224 (Locked)
LNB: 11250
22 KHz Tone: OFF
Multi-Dish Switch: SW 42 Dish 2
Search Options: ALL Channels
LNB Power: ON

Now - to the above set up (that works very well) how would one add the 12/15, 61.5.
1.) What Switch(es) shall be used, will SW21 work by itself or should it be combined with any other additional hardware?
2.) How it should be connected (connection diagram)?
3.) What will be the correct settings in receiver?
I have found answers to the above questions on similar setups but not exactly on this one (mostly on DishPro etc. which is a bit different) or receiver different.

A.)If you recommend equipment & connection (as per above questions), please if you can fill info in receiver settings (bellow):
Sat: 12/15, 61.5
DiSEqC: ????
DiSEqC 1.1: ????
TP Frequency:????
LNB: 11250
22 KHz Tone: OFF Turn to on
Multi-Dish Switch: ????
Search Options: ALL Channels
LNB Power: ON

B.) Will there be changes to settings on / to the 119 and 110 ? In all probability yes. Can you advice as well.

Thanks to all of you in advance. I would use a encoda 22KHz switch and put the 61.5 to the on side

[anarchista]

Pugsycan ... thank you. Will try. Got that type switch (maybe Ariza made) somewhere in my junk. Will post later how it went... but should work.