One touch recording not working if you change channels

Quote:

---

Originally Posted by Coaster

Hello,

Running Buzz 4900XR
I can only record the channel I'm watching. Was working fine for years and then poof?
Any ideas?
Thanxs

Coaster

---

Also noticed you opened a thread about his same issue in 2023 and was given a solution that worked.

I'm using the classic right now and I'm encountering the same issue. I believe last time I went through this I was using the 4900

Quote:

---

Originally Posted by Emporium

I have seen cases where a server gets a little overloaded and the number of connections it reports to the box are not correct. When channel surfing, as it opens another stream when you change channel, the previous stream take a long time to be detected by the panel as idle/disconnected and it detects it as a simultaneous stream.

So then when you start the recording, it assumes that it is at max streams, and therefore when you try to change channel after, it assumes there are no streams available. I have tested this with one panel and I would monitor the number of connections and as soon as the panel would release the "idle" connection, or I would manually kill it, then changing channel worked fine.

Unfortunately not much you can do on the user end, other than possibly waiting some time (could take up to a minute) for the idle connections to completely drop. I find (at least with the server I tested), that the issue was worse when the stream type was using HLS/M3U8. Switch stream type to TS seemed to help in dropping the connections quicker and the issue was less noticeable.

---

That makes total sense. I haven't responded sooner because sometimes it would record and sometimes not??
I was still testing when I read this and have changed to TS. Much better.
I'll chime back in and give a further update.
Thank you so much for your help.

Coaster

Quote:

---

Originally Posted by Maestro701

Also noticed you opened a thread about his same issue in 2023 and was given a solution that worked.

I'm using the classic right now and I'm encountering the same issue. I believe last time I went through this I was using the 4900

---

Not sure what I did that time either??
Changing to TS stream is working at the moment.
GL

Quote:

---

Originally Posted by Coaster

Not sure what I did that time either??
Changing to TS stream is working at the moment.
GL

---

I use hls and turned one button record off over a year ago on my 4900 and never a problem

Quote:

---

Originally Posted by dishuser

I use hls and turned one button record off over a year ago on my 4900 and never a problem

---

Thanks for the input, I'll give that a try if needed as TS is working now.
Thanks again all for your valuable input....cheers.
I'll toast you all, when Dryuary is over.

Coaster

NFG again.
Tried HLS and TS and Auto and none work???
I'm stumped.

did you turn one button record off and leave it off?

Quote:

---

Originally Posted by dishuser

did you turn one button record off and leave it off?

---

I just did that but you have to create a new schedule...not tough but no "one button recoring"
This is better than having to go to PVR and fill everything in.
Thanks again for chiming in.

Quote:

---

Originally Posted by Coaster

I just did that but you have to create a new schedule...not tough but no "one button recoring"
This is better than having to go to PVR and fill everything in.
Thanks again for chiming in.

---

I use it in case I want to make edits
if not I just click save

Quote:

---

Originally Posted by dishuser

I use it in case I want to make edits
if not I just click save

---

Definately better than going through the PVR route.
I'm still going to screw around and see if I can get it to work.

Now it's working after waiting for a few minutes. I think Emporium has it.
"waiting some time (could take up to a minute) for the idle connections to completely drop."
.... still testing......

Quote:

---

Originally Posted by Coaster

Now it's working after waiting for a few minutes. I think Emporium has it.
"waiting some time (could take up to a minute) for the idle connections to completely drop."
.... still testing......

---

I don't wait but just remembered I have 6 connections so that must be it...lol

Quote:

---

Originally Posted by Coaster

Now it's working after waiting for a few minutes. I think Emporium has it.
"waiting some time (could take up to a minute) for the idle connections to completely drop."
.... still testing......

---

I have 4 connections and currently experiencing the same thing. Tried a different service with 2 connections, same thing. I remember having this issue on the 4900 and I believe I had to reset the device for it to work again.

The fact it's not working on either service I have might be an issue otherwise. I have tried all the suggestions posted. This one is interesting

Quote:

---

Originally Posted by Maestro701

I have 4 connections and currently experiencing the same thing. Tried a different service with 2 connections, same thing. I remember having this issue on the 4900 and I believe I had to reset the device for it to work again.

The fact it's not working on either service I have might be an issue otherwise. I have tried all the suggestions posted. This one is interesting

---

I screwed up when I re load a few months ago and had to reset everything and it worked for quite a while.
I don't want to have to fill in all that stuff every time if I can help it.
Misery likes company so thanxs for letting me know I'm not alone. Sorry for you though!
I might try a full reset again and see how long it lasts?

Coaster

Quote:

---

Originally Posted by Coaster

I screwed up when I re load a few months ago and had to reset everything and it worked for quite a while.
I don't want to have to fill in all that stuff every time if I can help it.
Misery likes company so thanxs for letting me know I'm not alone. Sorry for you though!
I might try a full reset again and see how long it lasts?

Coaster

---

I don't normally do much recording so it's okay for me. When you brought it up again is what prompted me to try it so as to confirm. I am positive I had to reset. You can backup your stuff in the Buzz app and restore after reset. That way you don't have to enter all that stuff again. Good kuck