Is there a decimal-point or period on the remote? I could not fine it.
Printable View
Is there a decimal-point or period on the remote? I could not fine it.
thxQuote:
Originally Posted by squirtNcider
Ya I tried that and it did not work
Thankyou. But what happens when you use the box at another location? I would have to carry the T5 with me? Was going to ship a programmed box to my brother but I'm thinking this just won't work.Quote:
Originally Posted by lomchivok
I took mine to the cottage good signal and quality but would not hook up to a different internet
My junxbox is acting strange today. When I turned it on no signal went ito satelite settings and nimiq 1 says (30/62) 91.0w
Transponder says (22/29) no signal. Scanned it brought up all the guide but no picture. Went to guide and it just showed stations but no guide .I could go up down channels some come in on nimiq1 some on nimiq4 I have a single lnb..
Turned it back into satelite config on nimiq1 and have full signa, now with transponderlisting (9/29) 12355h 21500 ..
Dont know if Bev is changing things.
Found out bev is messing with sats everything to return
I got 1 from Tony as well, for future use.They are what you pay for & are not even close to the Dreamlinks/Sonicviews we got here with.The ethernet port is DOA on my unit (no status lights).The wireless works ok so far, but the unit is directly under my wireless router, so it should.
Setup is ok.When the time comes I will factory reset it & set it up for just the 91 sat.Not watching it for now anyways.
The picture quality is fair at best.HD is far from that of the Dreamlinks, & the HDMI has no audio output on this unit.I have to use RCA cables, but that will be fine for the living room, but not the home theater.It is what it is folks.
Anyone thinking ahead can get spare JB200 models at Amazon as we speak.I ordered 2 yesterday & they will be here middle of next week.
Pray that the software becomes open source for the Dreamlinks...lol.
The Dreamlinks are S.O.L. for New Firmware/Software Updates as far as I'm concerned, No one willing to take it onQuote:
Originally Posted by The Noof
Now that most have moved to IPTV etc.
junxbox when scanning cant find CNN and Detour as well as playboy and adult channels. why?Quote:
Originally Posted by auggie
Welcome to Bev & their changes that are on-going, I don't have a Junxbox so can't help you much on that
Other than the Junxbox is not a Jynxbox so not the same.
the junxbox is a jynxbox clone so apparently the section was already created
only for you :laughat:Quote:
Originally Posted by peterpeete
anyone have a factory junxbox bin backed up , mine is in er01 after loading a bin , need a loader and bin.
How do you save Junxbox info onto a flash drive? I can save user info ...but I want to save the firmware info. How is that done? there is no blue button at bottom of firmware screen like there is on user database...(my usb to rs232 adapter will not work with these clone boxes as far as I have tried)
I've got one of these boxes and the Ethernet/LAN MAC address is all zeros causing DHCP to fail, has anyone else see this problem with the Amazon purchased units?
did you try static?Quote:
Originally Posted by andrew867
Will connect to the internet on some routers but not others, Microtik can be tricked into working. It isn't a problem of static vs DHCP, as no network device should have a hardware MAC address of 00:00:00:00:00:00. The box will also get blocked by IKS providers if left on when not in use, while others don't support it fully as it sends 'bad data' when it is in standby on Ethernet.Quote:
Originally Posted by dishuser
Quote:
Originally Posted by andrew867
if anyone else sees this. this is correct. junxbox must not have coded MAC addresses into their ethernet adapters, so they all get the 00:00:00:00:00:00 MAC. Most routers don't like this and may not pass data to it, especially if you have a switch in your network.
On a side node, Got 2 of the junxbox's
JUNXBOX p2
Loader 1.2.20
Hardware version 1.0.24
database 1.0.1
firmware 1.2.59
Im connected to 91. and using the BEV channel list that is on the file section
https://www.satfix.to/showthread.php...ist-not-edited
But i am not able to get any EPG at all. nothing. I see in this thread people on the exact same version were able to get EPG..
could it be because of the bev channel list i uploaded?
I reset everything to factory, channels come in (with the channel list i uploaded) but no EPG.
Might someone be able to backup their 91 channel list and upload so i could try? Or does anyone have any ideas why i might not get EPG?
Thanks
what do ya know?
search still worx...lol
https://www.satfix.to/showthread.php...42#post1402942