I have noticed that the Jynxbox is not getting a 7 day EPG. Anyone recall it it was posable before the recent changes?
I only pull the Jynxbox out today was using Dreamlink.
Printable View
I have noticed that the Jynxbox is not getting a 7 day EPG. Anyone recall it it was posable before the recent changes?
I only pull the Jynxbox out today was using Dreamlink.
With what's going on with the changes, Personally I wouldn't worry about a 7 day EPG
Any EPG at this time is OK with me etc.
auggie,
That's not my point. I am wondering why it's does the EPG not work? Be nice to know if the EPG is working properly in a sub.
I just wonder that after some time they will fix something in the stream that allows it to work and other STB to scan channels again.
When the south provider did this everything worked. I just cant remember if they went from MPEG 2 to MPEG 4 HD or did they move some MPEG 2 to MPEG 4 SD also that's maybe the only difference.
Quote:
Originally Posted by jets
epg is working fine with ird subs
Hi all, I am using the Jynxbox...in an earlier post sat9182 said to: change your transponders 1- 18 on 91 to turbo 8psk and 21500 2/3a...
I don't understand, where do I change "to turbo 8psk" and what is "21500 2/3a", I'm not a technical person so you will have to walk me through it.
Any help you can provide would be greatly appreciated, as I just resubscribed and wasn't told or aware of these new problems with IKS, had I known I would have probably gone a different route. I'm a "play'n go", I have no techinical skills and at my age now it's just about watching tv.
Thanking you guys in advance.
Bev is doing a whole mess of changes/testing as of Now (MPEG 2 to MPEG 4 & others) for provider IRD's that may not be a problem on the EPG & Such, But for FTA Boxes it would be a problem cause they can't Auto adjust to the changes being madeQuote:
Originally Posted by jets
without updated software/firmware possibly, case in point the DL-HD-T5 looks like it's DOA OR DITW=(dead in the water)
Just my 2-cents worth
Read post #79Quote:
Originally Posted by Bayman1953
Would you be able to provide the link to post #79?Quote:
Originally Posted by auggie
look in the top right corner of postQuote:
Originally Posted by Bayman1953
you'll have to go back a page
I have changed the frequency on both transponders i have signal on both but my jynxbox keeps using a different transsponder. What am i doing wrong
you have to change ALL Sat. 91 TP's 1-19 using 21500 SR, 3/4A FEC and in TUBO8PSK modeQuote:
Originally Posted by Rickhardmb
I don't have a Jynxbox but it should be located in Dish settings heading under Transponder # bring up a list of 1-32 Transponder #'s this is where you should be able to edit each TP # as stated.
I have a SV8000, should I change all TP's to 21500 SR, 3/4A FEC and TUBO8PSK mode and rescan?
Read post #101 which apply's to all FTA Boxes that the TP's can be changed, for the time being, with whats happening currentlyQuote:
Originally Posted by bigbro
don't know if it will last or not, "My best Guess"
In the Jynxbox it is only necessary to change the mode from QPSK to TUROB and the symbol rate from 20000 to 21500.
Do this under manual scan, RED button for edit TP.
So, as of now, the only 2 receivers that 'may' work are the Jynxbox V6 and the sonicview 8000? A few friends and I all have DL HD or T5's so I've been looking around for replacements seeing that the DL boxes may be doorstops soon......
I came across a Viewsat 9000HD but thought I'd ask here first to be sure.
Also, are the HD boards in the DL receivers good for either of those boxes?