xx-client is set up and waiting for request. On the receiver the guide is setup and 101 has video and audio, all the rest are scramble. I need instructions on how to set up the receiver and the files to install. Thanks
xx-client is set up and waiting for request. On the receiver the guide is setup and 101 has video and audio, all the rest are scramble. I need instructions on how to set up the receiver and the files to install. Thanks
Post your menu settings - system information and utility settings
Menu:
Keyworks: autoroll off, EMU on
System:
SW: MVO2.53 (May 15) LDR 1.08
HW VER: 1.00
Duo/trio (4)
RS232 Mode: Normal
Using a serial cross over cable
Running Win 7
Thanks
Last edited by cgc; 10-03-2012 at 04:52 AM.
Hey cg
you need these files for receiver .
CNX DUO
FactoryTP_516_Factory_UPB 2/10/10
Third PartyTP_253_UPB 5/22/10
and null cable
Last edited by 1boxman; 10-03-2012 at 03:57 PM.
You can't help but use a null modem as the STB and PC both have male ports. Are you using a COM port or USB to serial? Check the port # in device manager and make sure it matches the Port in the Conf File. When connected you should get the following.
SW: MVO2.53 (May 15) LDR 1.08
HW VER: 1.00
Duo/trio (4)
xx-client v1.14
Also, EMU=off
RS232=Dongle, IP Setup, IKS
Last edited by jeldf; 10-04-2012 at 12:55 PM. Reason: added more info
SW: MVO2.53 (May 15) LDR 1.08
HW VER: 1.00
Duo/trio (4)
unknown
Com port settings are the same in the device manager and the xx client
RS232=Dongle, IP Setup, IKS
now the receiver is off service
(I setup coolsat 5000 like a snap, why is this duo driving me crazy)
Thanks for the help.
cgc
I will flash my Nano to a Duo and see if I can get it to work with those settings i love testing. Will let you know how it works out.
beg to differ......CNX Mini, Duo, Trio, Nano can all run each others software. been there, done it. Remotes become a little weird but you can always make one that will work.
Device Manager
com0com - serial port emulators
-com0com - bus for serial port pair emulator
-com0com - serial port emulator
-com0com - serial port emulator
ports (COM & LPT)
Bits per second 115200
Data bits 8
Parity NONE
sTOP BITS 1
XX-Client
[General]
serial_port=\\.\CNCA0
emulator_serial_port=\\.\CNCB0
receiver_serial_port=COM1
receiver_timeout=200
receiver_byte_read_delay=250
server_byte_read_delay=100
serial_port_settings=115200|8|N|1
byte_write_delay=50
receiver_protocol=0
caid_mappings=1840:1816
background_execution=0
debug_level=1
log_to_console=1
log_to_file=0
logfile_name=xx-client.log
control_words_timeout=12
card_server_url=newcamd://xxxxxxxx:[email protected]:99999/123456789123456789123456789
Client ready -Waiting for request
Receiver Configuration:
System information
SW:MV02.53 (May 15) Ldr 1.08
HW Ver. 1.00
USB 2.0 Driver: 1.00
Duo/Trio (4)
Unknown
Key Works
Key edit System1 Nagra
Reset data - not touched
auto roll, bev, dish - off
Emu - OFF
RS-232 Mode
Type - Normal
network - Network settings - not used (no addresses entered)
Registration IKS - registration failed
Null serial cable
If I set RS-232 Mode to Dongle then I get off service on the receiver.
So what is the set up procedure for the duo receiver. emu-off, rs232, is dongle or normal. do I enter ip addresses.
CNX Duo bins:
Factory: DTP_516_Factory_UPB
Third Party: DTP_253_UPB
CNX Settings:
emu = off
rs232 = normal
xx-client:
Receiver protocol to emulate = 1
You enter your private server info in xx-client and it should work at this point. Are your com0com virtual settings correct?
Last edited by dinkish; 10-26-2012 at 12:59 PM.
set rs232 to normal and I lost Snookie lol. rs232=dongle ;-) are you using USB to serial? you need to allocate the USB to Com1 in Device mgr for it to work with com0com.
HELP PLS
i am trying to setup my cnx duo for private iks and i am sooooo lost
i have installed xx-client and such and when i go to run it keeps saying it cant find cncb0 i am using windows xp