Results 1 to 7 of 7

Thread: CNX Nano 2

  1. #1
    Join Date
    Nov 2012
    Posts
    84
    Satfix Buxs
    368
    Thanks
    20
    Thanked 18x in 10 Posts

    Default CNX Nano 2

    In the beginning it work fine after I delete Satellite Channels it gave me ---- on stb .
    I did a hard boot power off @ a back stb and unplug for awhile but it still no change.

    Reload the 129 npn file it still do no change and factory files 805, to 810 it nothing happen but it gave me ERR5 on stb screen, than I converted Ilink to Nano2 original it show C 113 with red, and green dot lite.

    Everyone had any experience like these give me a hand I'll appreciated a lot
    plus I been read a lot posted but it still do no good for me

  2. #2
    Join Date
    Feb 2013
    Posts
    18
    Satfix Buxs
    96
    Thanks
    31
    Thanked 15x in 7 Posts

    Default

    have a look at the sticky "Recovery File" its in the Nano2 files section.

  3. The Following User Says Thank You to kdawg64 For This Useful Post:


  4. #3
    Join Date
    Sep 2012
    Posts
    332
    Satfix Buxs
    1,971
    Thanks
    1,232
    Thanked 464x in 184 Posts

    Default

    c113 means it's stuck in boot.

  5. #4
    Join Date
    Nov 2012
    Posts
    84
    Satfix Buxs
    368
    Thanks
    20
    Thanked 18x in 10 Posts

    Default

    I did look and work on whatever the file that said
    if I miss something just put in order maybe my stb will wake up again.

    I never had any bad time like this problem b4.

  6. #5
    Join Date
    Oct 2009
    Location
    SE of N...NE of S
    Posts
    3,401
    Satfix Buxs
    2,945
    Thanks
    6,690
    Thanked 4,077x in 1,531 Posts
    Items USACokeFriesTVDishBurgerBox of crappoison

    Default

    Found this while sniffing around on the net...maybe it will help and solve your issue:

    C/P...kudos to the author..
    -------------------------------------------------------------------------------------------------------------
    Problem solve. error (C113)

    Problem solve with the (C113) error in the front sreen of the cnx nano2 after rebooting from the back switch.
    Thanks to Whacked_out for the help

    How to get the (C108) Back after rebooting.

    If you have a converted nano2 to ilink.

    ilink back to NANO2
    Prerequisites:
    you must have the ilink 2.84 bin installed

    1. Reset to factory defaults.
    2. Upgrade receiver using the following file through USB stick: ILINK_TO_NANO2.ups. Use "S/W Upgrade" option on upgrade screen.
    3. Reset to factory defaults.
    4. Upgrade receiver using the following file through USB stick: NPN_1.29.NPN . Use "S/W Upgrade" option on upgrade screen.
    5. Reset to factory defaults. You are back to NANO2 NPN 1.29 .

    I loaded this bin with a USB
    .
    1- load bin NPN_809 factory.NPN
    2- factory default (very important)
    3- load bin NPN_8.10_ factory. NPN
    4- factory default ( very important)
    5- load bin NPN_1.29.NPN.

    Now convert back to nano2 to ilink
    NANO2 to ilink

    Prerequisites:
    - You must have NPN1.29 FW installed.

    Process flow:

    [NOTE: All factory resets are very important, the first time I tried doing this it didn't work and it was due to this step so do it!]
    1. Reset to factory defaults.
    2. Upgrade receiver using the following file through USB stick: NANO2_TO_ILINK.NPN . Use "S/W Upgrade" option on upgrade screen.
    3. Reset to factory defaults.
    4. Upgrade receiver using the following file through USB stick: IR2x0_2.84.ups . Use "S/W Upgrade" option on upgrade screen.
    5. Reset to factory defaults. You now have 2.84 ilink BIN installed. It is good to go.

    This is how i fix the (C113) error and got it back to the (C108).

    Thanks and enjoy.
    --------------------------------------------------------------------------------------------------------------
    End C/P

  7. The Following User Says Thank You to abouttosnap For This Useful Post:


  8. #6
    Join Date
    Nov 2012
    Posts
    84
    Satfix Buxs
    368
    Thanks
    20
    Thanked 18x in 10 Posts

    Default

    I been working with these Nano2 all kind instruction but still can't solved or get my STB off from C 113.
    What ever I load or flash, at the end hard boot from the back it came back C 113. Is it really a heart bit
    STB put on me and can't done couple days already.

  9. #7
    Join Date
    Oct 2009
    Location
    SE of N...NE of S
    Posts
    3,401
    Satfix Buxs
    2,945
    Thanks
    6,690
    Thanked 4,077x in 1,531 Posts
    Items USACokeFriesTVDishBurgerBox of crappoison

    Default

    Don't know if it will help but check the thread below.

    http://www.satfix.net/showthread.php...-not-work-HELP

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •