Results 1 to 3 of 3

Thread: How to for true FTA channels.

  1. #1
    Join Date
    Oct 2009
    Posts
    9,003
    Satfix Buxs
    4,002,465
    Thanks
    3,658
    Thanked 8,666x in 3,246 Posts
    Items PhoneHeartVintage truck
Gift received at 12-23-2012, 09:06 AM from ICEMAN
Message: thank you budTVCoffee makerPinkfloydthe travel gnomeTractor

    Default How to for true FTA channels.

    How to for true FTA channels.

    First is to go to a site like Lyngsat.com or Satbeams.com and look for the free channels you want to view and what satellite they are on, 90% are on what are called linear satellites..

    There are lots of satellites with free channels on them but trying to get them all on one satellite dish may prove to be too difficult for some.

    The first thing you are going to need is a good dish, a larger dish then to one your currently using for Dish or BEV (if you are) is needed to view these satellites as they are lower power then the ones Dish and BEV use, they also need a different LNB then the Dish and BEV satellites, the Dish and BEV satellites are circular polarized, the FTA satellites are linear.

    A 39” to 48” dish is a good start, also a good low noise floor linear LNB is required, most start at .4 dB the better ones can go as low as .1 dB, the type of dish you use depends on how many satellites you need to receive, a round dish is called a prime focus dish as most of the signal is directed to one point, this is where a single LNB would be centered, other LNB’s could be used but it would be best to get an elliptical dish as it would provide more signal to a lager spread of LNB’s.

    Most elliptical are 24 x 36 inches for linear satellites, some can hold as many as 5 LNB’s, there are others that can use more LNB’s, the better ones are the T55 and T90, these are very large and required special LNB’s to work.

    Another way to go is with a motorized system, this would use 1 round dish around 39” to 48” depending on the motors spec’s as to what it can handle, also your location would determines the size of dish your going to use, the further North you are the larger the dish will have to be

    With a motorized system you can pan the entire belt of satellites visible at your location, a good LNB for this application would be one that has both circular and linear capabilities.

    With a 4 input DiSEqC switch you could use 4 dishes with a single LNB on each, this would give you the best setup as you can individually focus each dish on a single satellite for maximum gain on that bird, if you have more then 1 receiver a second switch could be used as most LNB’s have 2 or more outputs, 3 or more receivers would require the use of a 4X4 switch, there are many different types and brands of switches out there, we can look at that later.

    So now you have decided on the satellite(s) you want to watch and the types of switches (if needed) and other hardware your going to use you then need to find that satellite, there are several good satellite location web sites out there, one is dishpointer.com, using that site and finding the bird you want is not that hard if you follow the directions posted for your location.

    Setting up the receiver for that satellite is the next step, as there are many different brands of revivers out there it would be impossible to describe the setups for all, so a generic way is to look at LyngSat for a transponder with an active free channel on it, these are marked with an FTA in the channel listing.

    To help with this you can ask on this site and someone would be glad to tell you what active channels are on that bird, setup help for your receiver is also available
    ♫♫♫ I’m a lumberjack and I’m OK ♫♫♫ I drink all night and sleep all day. ♫♫♫



    Coming soon to a crop circle near you.....

    There is a 66 and third % chance that I'm on the right planet...

    "I'm happier then a Jackalope in a balloon factory"

    "First rule of testing satellites"
    "If its working fine now, then don't mess with it"

    "Second rule of testing satellites"
    "If you did mess with it, and now it doesn't work, can you blame someone else?"

    "Third rule of testing satellites"
    "If you did mess with it, and it doesn't work now, and you can't blame someone else"
    "Can you HIDE it"?

  2. The Following 2 Users Say Thank You to Terryl For This Useful Post:


  3. #2
    Join Date
    Oct 2012
    Posts
    40
    Satfix Buxs
    1,181
    Thanks
    13
    Thanked 13x in 8 Posts

    Default

    It's also good to keep in mind you get a compatible receiver for this for the channels you wish to receive. Some channels are broadcasted in DVB-S, some in DVB-S2, and are modulated differently, some QPSK 4.2.0, QPSK 4.2.2, 8PSK 4.2.0, and 8PSK 4.2.2. Some are also C Band (Big Ugly Dish) and some are Ku Band (Smaller dish). Long story short a lot of the most popular fta receives don't support all these available formats so it's important to, when getting a receive, pick one that gets the channels you want.

  4. The Following 2 Users Say Thank You to solaris For This Useful Post:


  5. #3
    Join Date
    Oct 2009
    Posts
    22,808
    Satfix Buxs
    2,206,753
    Thanks
    36,982
    Thanked 26,260x in 7,930 Posts
    Items GreeceCanada

    Default

    It would be nice to get a receiver that would be compatible with all the above mentioned formats but the only one I can think of is the azbox. Most true fta receivers now are almost all s2/8psk compliant, just a matter of how much you want to spend for what your looking for.







Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •