XFTA Setup Help

[mishtag]

I am trying to use my CW800s with XFTA router using X-fta-xx-client-920-Techno-Cyber for the router and bin files v2.66 (I also tried v2.42) and after following different instructions which most are the same with some differences, I still can't make it working, so would you please help me by answer the following questions:

1. please confirm the below ini files setup.
2. how to see if the xfta is connected (X-fta-xx-client-920-Techno-Cyber doesn't have log viewer).
3. there is no run and stop buttons, does it mean it is running as long as it is connect to power?

Note: I have replace the user id and password with 111 and the domain with aaa.

caid.ini
# Up to 8 CaID's can be remapped.
#1841=1815
1802:1816

servers.ini
# Up to 8 servers can be listed here.
111111111111:111111111111@aaaaaaaaaaaaaaaaa:35955/6103403445406970987123412134
# Example:
# [email protected]:50060/1234123412341234123412341234
# [email protected]:50061/1234123412341234123412341234
# [email protected]:50062/1234123412341234123412341234
# [email protected]:50063/1234123412341234123412341234
# [email protected]:50064/1234123412341234123412341234
# [email protected]:50065/1234123412341234123412341234
# [email protected]:50065/1234123412341234123412341234

xx-client.ini
# Serial port receiver is connected to.
serial_port=/dev/tts/0

# Set baud to 19200 for most Viewsat, XFactor and CNX receivers that used
# a dongle.
# Set baud to 115200 for most other receivers and Viewsats running SSSP
# firmware.
serial_speed=115200

# Control word retrieval timeout in seconds.
server_timeout=10

# Number of attempts before connecting to a new server. Setting to '0' will
# make the client try the next server after first failure.
server_retries=1

# Receiver protocol
# 1 - Viewsat/X-Factor
# 2 - CNX
# 3 - SSSP Viewsat/SSSP Pansat/Coolsat
# 4 - Captiveworks
receiver_protocol=4

# If set to 1, CaID reported by the receiver will be ignored and ECM will be
# sent to server even if there is a CaID mismatch. If you are using a single
# provider you should set this to 1.
ignore_caid=1

[greg]

like this

1841=1815
1802=1816

[xx-client.ini]

servers.ini

[email protected][/email]:50060/1234123412341234123412341234
# [email protected][/email]:50061/1234123412341234123412341234
# [email protected][/email]:50062/1234123412341234123412341234
# [email protected][/email]:50063/1234123412341234123412341234
# [email protected][/email]:50064/1234123412341234123412341234
# [email protected][/email]:50065/1234123412341234123412341234
# [email protected][/email]:50065/1234123412341234123412341234

xx-client.ini
# Serial port receiver is connected to.
serial_port=/dev/tts/0

# Set baud to 19200 for most Viewsat, XFactor and CNX receivers that used
# a dongle.
# Set baud to 115200 for most other receivers and Viewsats running SSSP
# firmware.
serial_speed=19200

# Control word retrieval timeout in seconds.
server_timeout=10

# Number of attempts before connecting to a new server. Setting to '0' will
# make the client try the next server after first failure.
server_retries=1

# Receiver protocol
# 1 - Viewsat/X-Factor
# 2 - CNX
# 3 - SSSP Viewsat/SSSP Pansat/Coolsat
# 4 - Captiveworks
receiver_protocol=1

# If set to 1, CaID reported by the receiver will be ignored and ECM will be
# sent to server even if there is a CaID mismatch. If you are using a single
# provider you should set this to 1.
ignore_caid=1

[mishtag]

greg, do you have spaces before the username? and I think you are using serial speed 19200 because your receiver is Viewsat, while I have to use 115200 for CW800s, correct?

[greg]

yes set to 115200 for your receiver and the username and password like this
xxxxxxxxxxxx:[email protected]:35922/6103403445406970987123412134
# username[email protected]:50062/1234123412341234123412341234
# username[email protected]:50063/1234123412341234123412341234
# username[email protected]:50064/1234123412341234123412341234
# username[email protected]:50065/1234123412341234123412341234
# username[email protected]:50066/1234123412341234123412341234
# username[email protected]:50067/1234123412341234123412341234

[mishtag]

After spending many hours to setup my xfta, I have received answer from poroto40 that file X-fta-xx-client-920-Techno-Cyber is not working with cw800s, therefore, I will start over with a new file xfta-o8.09.2-g1.2.3-wf0.23mex-hgdvb.trx.