discussion of bev tp changes

[jets]

The time for lock is that the Jynx STB has to read data from the stream being downloaded.

[brunoc]

I have MegaTvi SHD 3000 receiver after manually making changes to the new/changed transponders i got
my sd channels working again.

[bizee]

On jynxbox, transponder changes worked and channels come in, however I had deleted a couple channels that are on these and now when doing a scan, it doesn't find channels and says 'skip', so now these missing channels won't come back in. Are they gone forever now or is there a way to get them back. Tried searching this site and the web and can't find solution.

[auggie]

You could try scanning just the TP's those missing channels were on, not sure if they will come back or not but worth a try

[bizee]

Tried that and it starts scanning then ends then says'skip', then no program found. Gets good signal but takes almost 4 secs in Maybe this delay didn't give it time to catch anything.

[auggie]

Tried that and it starts scanning then ends then says'skip', then no program found. Gets good signal but takes almost 4 secs in Maybe this delay didn't give it time to catch anything.

You need to give it time to find stuff, mine would do the same, (skip a TP) then it would come back to it once locked on ?

[blackjack]

If you have a Junxbox from Ali it's missing a few TPs on 91 from the factory and you have to re-add them. Check LyngSat list against your box's list to be sure, but I think it's 12370V/21500/8PSK, 12457H/21500/8PSK, 12282V/21500/8PSK, and 12457V/21500/QPSK. I think 2 or 3 of those have channels on them so they're not just useless.

[azs2000]

On Sat 91W, I am not getting signals for TP 12224 to 12414 and 12457, 12472, and 12486. However, getiing signals for TP 12428 to 12676. As per

www.lyngsat.com

, Bell changes symbol rate for all these channels from 20000 to 21500 and and transmission to "Turbo 8PSK" (using Dreamlink T5). After changing the symbol rate and transmission still no luck. No signals for those TP yet. Does anybody know anything else to resolve this issue?

[auggie]

Yes Dreamlinks are Toast or Basically Door stops, they can't handle the TP changes with-out
Software/Firmware updates, & that isn't about to happen anytime Soon or ever.

[john deer]

I have a dreamlink that has worked flawlessly for many years. I also have Jynxbox Ultra HD v30 that was purchased just as a spare. Plugged it in this morning and it does work also. Is there a way for me to add the info needed in the box to get the missing or changed channels on Nimiq 1. Have not had to make any changes since all has worked for many years Thanks

[auggie]

I have a dreamlink that has worked flawlessly for many years. I also have Jynxbox Ultra HD v30 that was purchased just as a spare. Plugged it in this morning and it does work also. Is there a way for me to add the info needed in the box to get the missing or changed channels on Nimiq 1. Have not had to make any changes since all has worked for many years Thanks

For the Dreamlink you are S.O.L. They are Door Stops Now, can't handle the changes with-out Software/firmware updates
and that isn't Going to happen anytime Soon. The Jynxbox can handle the changes, TP's 1-thru-19 need to be changed

[john deer]

That's great news. I have been reading info on the Jynxbox, but still haven't been able to see how to make the TP changes. Where can I find out how to do this. Thanks in advance

[dishuser]

That's great news. I have been reading info on the Jynxbox, but still haven't been able to see how to make the TP changes. Where can I find out how to do this. Thanks in advance

did you ever consider reading in the jynxbox section?

[john deer]

I have been reading that section but can't seem to find what I need

[auggie]

I have been reading that section but can't seem to find what I need

Read through this section: https://www.satfix.to/showthread.php...ltra-HD-V2-fec