discussion of bev tp changes

[dishuser]

Hi where do you find the TP in the settings on a dreamlink t5 thanks

fill it with cement and go to the nearest bridge

[The Noof]

fill it with cement and go to the nearest bridge

ROTFLMAO DU.
Don't waste the cement:it will sink in any case.

[jets]

I actually made a small but maybe big step in identifying the problem. I took my channel list with the non working 91 channels and opened it up in the Jynxbox channel editor. Problem is I think the editor is from the original Jynxbox team not the clone group.

However I was able to read the file and I noticed that a value called a "ONID" in the TP's that don't work, the value was 0 and in the working TP's the value was 256. So I made the edit and loaded it back in to my Jynxbox Lite and it bricked that box. Lucky I was able to bring the box back with the special RS232 cable that box uses 9 pin serial on one end and 3.5mm stereo jack on the STB end.

Here is an attachment of the cable needed for that box but I suspect it comes with it when you got it new.9m351m-rs232-cable_datasheet.pdf

So I think the Jynxbox Editor clone killed my device but not before I was able to see a possible issue. If we could edit that channel dump file we might be able to fix it. I will take another go at it tomorrow night see if I can get it to work with editor somehow?

[dishuser]

try a hex editor

[jets]

Ya I tried to open in notepad LOL. But yes HEX editor. I know once you make the change you have to correct the checksum. Hopefully I can do that, it's been a while...

[UNVMYRZR]

I know this might sound weird but out of boredom I was randomly entering LNB frequencies and now I have a signal of 97 and quality of 95. My settings are as follows
LNB Power - ON
LNB Type - single
LNB Frequency - 11.050 (manually entered on T5)
LNB 22KHZ - on
Is it possible that just entering the correct frequency manually might solve this problem? I have been at it for a couple hours now just to get this far. Or am I wasting my time?

[dishuser]

do you get the channels that have changed?

[UNVMYRZR]

do you get the channels that have changed?

I haven't found the combination yet, its quite tedious making the manual entry then going back out and in and changing and checking but Im trying.

[jets]

What box (STB) are you using?

[UNVMYRZR]

What box (STB) are you using?

T5 Dreamlink. Im changing the frequency manually by 5 and only found the one combo that increases the signal strength and quality. I am working my way down in numbers now. even though it is showing the increase on the settings page, it is not changing when on the guide while on one of the missing channels. I might be wasting my time but you never know. if I get higher S/Q then I go up/down by single digits on frequency. so its time consuming.

[JimmyZ]

You're wasting your time. The T5 is going to be a doorstop very soon. Sucks seeing I loved the 3 I had up and running for many years.

[jets]

Why would it be a door stop, all the HD works, plus the guide channel is still SD on 91 TP 14228.

[auggie]

Why would it be a door stop, all the HD works, plus the guide channel is still SD on 91 TP 14228.

If HD is on 82, I keep hearing & people keep saying that 82 is Done or almost Done. ? Plus the fact that Dreamlinks are not
open source Software/Firmware, like some of the other FTA Receivers that are.

[jets]

They can say all they want but HD works here on a Dreamlink.

Thing about IKS overall is the low bandwidth, not everyone can stream IPTV, most but not all. In rural areas where I am high speed internet is only available by Starlink.

[anthonym41]

is anyone getting nfl sunday ticket if so what are the settings please